SPECIFICATIONS
Input Impedance: | 20K Ohms balanced |
| 10K Ohms unbalanced (1/4") |
Output Impedance: | 50 OhmsTRS Balanced |
Max Input Level: | +10 dBV XLR |
| +10 dBV 1/4" |
Phase Shift: | < 10 deg. 20 Hz - 20 kHz |
Input Connectors: | XLR and 1/4" |
Phantom Power: | 36 Volts DC |
Outputs: | 1/4" main balanced +17 dB max |
| 1/4" monitor +17 dB max |
| 1/4" FX send |
| 1/4' TRS Stereo Headphone |
Max Gain: (Mains): | 60 dB bal/unbal |
(Monitor): | 55 dB |
Tone controls: | 12 dB treb, bass cut/boost, 1K Hz center |
Max S/N Ratio: | 106 dB |
THD: | < .003% |
IMD (SMPTE): | < .003% |
CMRR: | 80 dB |
Power: | AC adapter 12 VAC (Rolls PS12) |
Weight: | 7 lbs (3KG) |
Size: | 19" x 1.75" x 6.5" (48cm x 4.5cm x 17cm) |
NOTES:___________________________________________________________
5
TREBLE: Controls the boost or cut of frequencies above 400 Hz for each channel.
PAN: Adjusts the amount of relative signal to the Right, Left or both Main Out jacks.
FX SEND: Controls the amount of signal
MASTER CONTROLS
FX RETURN: Adjusts the amount of signal coming back into the FX Return jack.
MASTER VOLUME, RIGHT - LEFT: Controls the amount of signal sent out the main Right and Left Output jacks, and sets the overall signal level except for the Monitor Send and Effects Send jacks.
REAR PANEL
MODEL RM65b | SERIAL NUMBER |
|
|
|
|
|
| CHANNEL 6 | CHANNEL 5 | CHANNEL 4 | CHANNEL 3 | CHANNEL 2 | CHANNEL 1 | |||
65- |
|
|
|
|
|
|
| MIC | MIC |
| MIC | MIC | MIC |
| MIC | |
|
|
|
|
|
|
|
|
|
| |||||||
MADE IN U.S.A. |
|
|
|
|
| STEREO |
|
|
|
|
|
|
|
|
|
|
LEFT | RIGHT | MONITOR | STEREO | FX | AUX BUSS | PHANTOM | LINE/ | TRIM | LINE/ | LINE/ | LINE/ | TRIM | LINE/ | LINE/ | ||
| OUTPUT | OUTPUT | SEND | FX RETURN | SEND | INPUT | TRIM INSERT | INSERT | TRIM INSERT | TRIM INSERT | INSERT | TRIM INSERT | ||||
|
|
|
|
|
|
| POWER |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| 6 | 5 4 3 2 1 |
|
|
|
|
|
|
|
|
POWER |
|
|
| TRS STEREO |
| TRS STEREO |
| WARNING: DO NOT EXPOSE THIS EQUIPMENT TO RAIN | CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT NOT REMOVE BACK. | RISQUE DE CHOC - NE PAS ENLEVER | ||||||
12 VAC |
|
|
| PLUG ONLY |
| PLUG ONLY |
| |||||||||
|
|
|
|
|
|
| OR MOISTURE. |
| NO USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. |
| ||||||
POWER: Connects to the Rolls PS12 12VAC, 300mA power adapter.
1 - 6 CHANNEL MIC INPUTS: XLR input connectors for mic or line level signals.
1 - 6 CHANNEL LINE INPUTS: 1/4” input connectors for line level signals.
Each of these inputs may be reconfigured as INSERTS by moving jumper connector for each channel located inside the RM65b.
TRIM: Adjusts the amount of input signal from the mic and line input jacks.
PHANTOM POWER: 6 switches for turning on the microphone phantom power for the XLR inputs, and are numbered for the channel they are assigned to. DOWN is on, UP is off.
AUX BUS IN: 1/4” TRS stereo input to the main mix bus, and may be used as an auxiliary stereo input for joining two RM65s together.
FX SEND: 1/4” unbalanced jack for sending the signals assigned by each channel’s FX Send control out to external effects.
FX RETURN: STEREO 1/4”
external effects devices. NOTE: THIS JACK IS STEREO ONLY - CONNECTING
A MONO
MONITOR OUT: 1/4” unbalanced jack for sending signals assigned by each channel’s monitor output control to an auxiliary amplifier or monitoring system. RIGHT and LEFT OUTPUT: 1/4” TRS balanced jacks to be used as the unit’s main outputs.
USING PHANTOM POWER
Phantom power is a means of powering condenser microphones through the micro- phone cable. The RM65b has individually switchable 36 volts of phantom power for each of its 6 channels through the XLR jacks. The DIP switches on the rear of the unit are for switching the power on and off. When the little switch tab is down, the power is on. The number on the switch corresponds to the channel that is receiving the power. If phantom power is not needed, it should be switched off to avoid possible damage
to a microphone, or degraded sound quality. | 2 |
