3.5" SATA to USB 3.0 & eSATA External Enclosure
user manual
STEP42 SlidePull outthetheHDDHDDintoplasticthe asetray.and push HDD inwardly until SATA NOTICEHardEnclosureSTEP4DriveTheFigureFormatInstalla“NewDescriptionngPartitionGuideWizard”
connector well connected. will appear. Please follow
Note:* YouPleasemay formatfollowyourthe instructionsHardDrive byto usingmake thesureUSByourconnectionHard Drive. is properly installed the "New Partition Wizard"
* FrontPleaseintoViewmakethe Externalsure yourEnclosureExternal Enclosure is turned on and connected to the step by step to complete
PC beforetheformattingHard DrivetheformattingHard Drive.
STEP1 Pushprocedurethe cover. “Buckle” inwardly to lift plastic cover up.
STEP1 | A |
and select “Manage”. |
STEP5 | Once the Hard Drive formatting |
|
|
|
|
|
|
| ||
| Question： | B |
|
|
|
|
|
|
| |
| procedure is completed, the |
|
|
|
|
|
|
| ||
STEP3 | Does this SATA enclosure support hot swap? |
| ||||||||
Place 3.5” SATA HDD wwwinto the.rosewillplastic tray and.comscrew the HDD on it. |
| |||||||||
STEP2 | Hard Drive will be recognized |
|
|
|
|
|
|
| ||
asSelecta “New“DiskVolume”Management”(New |
|
|
|
|
|
|
| |||
STEP5 | Answer： |
|
|
|
|
|
|
|
| |
Close the top cover until the buckle is locked. |
|
| ||||||||
| Volumeand you drwivell seel ttyourmayHardvary |
|
|
|
|
|
| |||
Rear ViewYes, but it depends on the motherboard you have. |
|
| ||||||||
| Drive. . “NewshownVolumeas | (Z:)” ) |
|
|
|
|
|
| ||
| 1. |
|
|
|
|
|
|
|
|
|
| “Unallocated” (Disk number |
|
|
|
|
|
| |||
| If your motherboard has an eSATA port in the Back I/O Connectors |
|
| |||||||
| mayPanelvary)as shown inDpicture # 1 . Your |
|
| |||||||
|
|
|
|
|
| |||||
| and there is no need to install the eSATA bracket. All you need is |
|
| |||||||
| connecting the enclosure with eSATA port at the back of your |
|
| |||||||
|
|
|
|
| 3.5" SATA to USB | 3.0 & | ||||
| computer. You can connect/disconnect the enclosure with your | |||||||||
|
|
| eSATA External Enclosure | |||||||
| computer at anytime. |
| RDEE |
| ||||||
STEP6 | 2. |
|
|
|
| |||||
|
|
|
|
|
|
| ||||
with an onboard SATA port and |
| no | ||||||||
STEP3 | If your mo |
| only comes |
| ||||||
therboardnE “Unallocated”C F |
| G |
|
|
| |||||
| You will see “New Volume” |
|
|
|
|
|
|
| ||
Thank you for purchasing a |
| |||||||||
| boxeSATAand selectport available“New Partition”. This mean. | |||||||||
| appear on your PC (Drive |
|
|
|
|
|
| |||
| motherboard. You will need to install an eSATA bracket. Since | |||||||||
| (Disk number may vary) |
| User Manual | |||||||
| letter may vary i.e. “New |
|
|
|
|
|
| |||
Please register your product at : www.rosewill.com for complete warranty | ||||||||||
| ||||||||||
| Volume (Z:)”)A Ventilation design |
| E Power Jack | |||||||
information and future support for your product. | ||||||||||
| computer while it powered off. The computer will recognize the | |||||||||
| B | Cover Buckle |
| F USB3.0 Port | ||||||
If you henclosuave anyrequestionduring thewhilebootingusingsequencesour products,andpleaseyou shouldvisit ourbe websiteableto : www.rosseewilltheC.drivecomFanafterControlMS WindowsKnob boot upG. eSATA Port
