Infrared Thermometer
User Manual
English
Thermometer Operating Instructions
The thermometer is a
STORAGE & CLEANING
The sensor lens is the most delicate part of the thermometer. The lens should be kept clean at all times, care should be taken when cleaning the lens using only a soft cloth or cotton swab with water or medical alcohol. Allowing the lens to fully dry before using the thermometer. Do not submerge any part of the thermometer. The thermometer should be stored at room temperature between
LCD ERROR MESSAGES
The thermometer incorporates visual diagnostic messages as follows:
|
|
| ‘Er2’ is displayed when the thermometer is exposed to rapid changes in the ambient |
「 | 」 |
| temperature. ‘Er3’ is displayed when the ambient temperature exceeds 0oC(32°F) or +50oC |
|
|
| (122°F). |
|
|
| The thermometer should be allowed plenty of time (minimum 30 minutes) to stabilize to the |
「 | 」 | working/room temperature. | |
|
|
| Error 5~9, for all other error messages it is necessary to reset the thermometer. To reset it, |
|
|
| turn the instrument off, remove the battery and wait for a minimum of one minute, reinsert |
「 | 」 |
| the battery and turn on. If the error message remains please contact the Service |
|
|
| Department for further assistance. |
|
|
| ‘Hi’ or ’Lo’ is displayed when the temperature being measured is outside of the |
「 | 」「 | 」measurement range. | |
|
|
|
|
BATTERIES
The thermometer incorporates visual low battery indication as follows:
(Default Screen)
1.Simply aim the thermometer at the measure target with Lens (4) and press Meas. key (6) to display the surface temperature.
2.During the measurement, the MAX reading will be displayed beside the 
icon.
3.The Distance:Spot is 8:1. Please make sure the target area is within the field of view.
ADD VALUE:
oC or oF | Press Mode key (2) for oC or oF transferred. |
Backlight | LCD Backlight: always on. |
|
|
Laser | ClassII Laser: always enable while measuring. |
|
|
EMC/RFI
Readings may be affected if the unit is operated within radio frequency electromagnetic field strength of approximately 3 volts per meter, but the performance of the instrument will not be permanently affected.
* Note: Under the electromagnetic field of 3V/m from 350 to 550MHZ, the maximum error is 8°C (14.4°F).
CAUTION
1.WHEN DEVICE IS IN USE, DO NOT LOOK DIRECTLY INTO THE LASER
2.USE EXTREME CAUTION WHEN OPERATING THE LASER.
3.NEVER POINT THE DEVICE TOWARDS ANYONE’S EYES.
4.KEEP OUT OF REACH OF ALL CHILDREN.
‘Battery OK’: | ‘Battery Low’: battery needs to be | ‘Battery Exhausted’: |
measurements are possible | replaced, measurements are still possible | measurements are not possible |
When the ‘Low Battery’ icon indicates the battery is low, the battery should be replaced immediately with AAA, 1.5V batteries. Please note: It is important to turn the instrument off before replacing the battery otherwise the thermometer may malfunction. Dispose of used battery promptly and keep away from children.
SPECIFICATION
Measurement Range | ||
|
| |
Operating Range | 0~50°C (32~122°F) | |
|
| |
Accuracy, | ||
| ||
Accuracy (Tamb=23 +/- 3°C) | ||
| ||
Emissivity | 0.95 fixed | |
|
| |
Resolution | 0.2°C/0.5°F | |
|
| |
Response Time (90%) | 1sec | |
|
| |
Distance:Spot | 8:1 | |
|
| |
Battery Life | Typ.18, min 14 hours continuous use | |
|
| |
Dimensions | 172.9 x 36.0 x 71.5mm(6.80×1.42×2.81 inch) | |
|
| |
Weight | 152 grams(5.36 oz) including batteries (AAA*2pcs) | |
|
|
** The thermometer will automatically shut off if left idle for more than 15sec.
Ref.No.：052010
