DX9000 - USA 13.05.2003 15:04 Uhr Seite 2
IMPORTANT SAFETY INSTRUCTIONS
When using this appliance, basic safety precautions should always be followed including the following:
Read all instructions before using this product.
• Use appliance only for its intended use. |
• To protect against a risk of electric shock, do not immerse |
the appliance in water or other liquids. |
• The appliance should always be turned off before plugging |
or unplugging from outlet. Never yank the cord to disconnect |
from outlet, instead grasp plug and pull to disconnect. |
• Always disconnect appliance from electrical outlet when |
filling with water or emptying when not in use. |
• Do not allow cord to touch hot surfaces. Let iron cool |
completely before putting away. Loop cord loosely around |
iron when storing. |
• Do not operate appliance with a damaged cord or if |
appliance has been dropped or damaged. |
• To avoid the risk of electric shock, do not disassemble the |
appliance. Ship it to the nearest authorized Rowenta |
approved service center for examination and repair. |
Incorrect reassembly can cause a risk of electric shock |
when the appliance is used. |
• Not intended for use by children. Close supervision is |
necessary for any appliance being used near children. |
Unsupervised use can result in fire or personal injury. |
Do not leave appliance unattended while plugged in, |
on an ironing board, or while it is still hot. |
• Burns can occur from touching hot metal parts, hot water or |
steam. Use caution when you turn a steam iron upside |
down. There may be hot water in the reservoir. |
• Do not direct steam at people, animals or iron clothes while |
they are being worn. |
• The use of accessory attachments is not recommended by |
Rowenta and may result in fire, electric shock or personal |
Before use
•Remove soleplate cover before using iron.
Remove all packaging from the iron.
•Please read all of the instructions for use and the Important Safeguards carefully.
•It is normal for a small amount of smoke and a light odor to be produced the first time it is used. This will quickly disappear.
Helpful Hints
•When ironing start with fabrics that require a low tempera- ture setting (•) and finish with those which need the highest temperature (•••).
•Mixed fiber fabrics should be ironed on the temperature for the most delicate fabric. For example a shirt that is 60% cotton and 40% polyester should be ironed at the (•) setting for synthetics.
•If spray starch is used, spray it onto the reverse side of the garment. Allow starch to penetrate before ironing by set- ting garment aside for 30 seconds.
•For best results, use a mesh type ironing board to allow excess steam to escape.
•For delicate fabrics, we recommend carrying out a test on an unobtrusive area of the garment such as an inner seam.
•Adhere to manufacturer recommendations on garment label.
Light Display System (depending on model)
Some models of the Perfect iron are equipped with an LED Light Display System. This system will inform you when the iron is heating and when it has reached ideal temperature. It will also notify you when the
3 Way Auto-Off (depending on model)
If your iron is equipped with
Models equipped with
Models equipped with LED Display System – The LED Light Display System will flash all 3 colors alternately when the feature has activated. To deactivate feature, move the iron or shake it gently. Wait until iron is fully reheated before use.
Filling
• Ensure the iron is unplugged.
• Slide the variable steam lever to the left (min).
• Rest iron on heel and tilt it forward approxi- matley 1 inch. Open the water filler inlet by pressing the
• Fill with water to the max mark on the water tank. We recommend using a water pitcher rather than filling under the tap. Iron holds approximately 13 oz of water.
• Close the filling inlet by pressing the push- button. Be sure to close before returning to the horizontal position.
Softened water
There are many types of household water softeners and the water from many of them is perfectly acceptable for use in an iron. However, some types of softeners, particularly those that use chemicals such as salt, can cause the appliance to leak or spit during use. If you experience this type of problem, we recommend that you try using bottled spring water or untreated tap water. Never use 100 % distilled water.
Once you have changed water it will take several uses to correct the problem. Rowenta recommends trying the steam function for the first time on an old towel or cloth that can be discarded to avoid damaging your clothes.
Iron and other impurities
If your water supply contains large amounts of iron or organic matter, these minerals can collect inside the appliance and eventually appear as brown stains. If you experience these problems Rowenta recommends using bottled spring water. Never use 100 % pure distilled water.
Always remember:
Battery water and water containing additives (such as starch, perfume or fabric conditioner condensed water from driers) may not be used. Such additives can affect the properties of the steam and, at high temperatures, can form deposits in the steam chamber, which will mark the laundry when they are emitted through the steam vents.
Descaling liquids/agents should not be used.
Selecting the Temperature
Models equipped with a temperature dial – Set the temperature control dial according to the fabric you are ironing. Check the gar- ment’s label for appropriate setting. We recommend using the chart below as a guide. Light will be on as iron is heating. When light goes out iron is ready to use.
Ironing label | Fabric | Temperature control |
Synthetics e.g.
Steam Ironing
WARNING: Never Iron or steam clothes while they are being worn. When iron is placed on heel, it will burst one more time before Intra Steam stops. Use caution and do not direct soleplate at people, animals, etc.
Before ironing for the first time fill iron and allow to heat. The iron should be allowed to emit steam for at least
1 minute to remove any impurities. Meanwhile press from time to time the burst of steam button. This should also be done if iron isn’t used regularly.
Intra Steam (depending on model) –
The Intra Steam system generates higher steam pressure to enable the steam to
penetrate faster and deeper into the fabric. The steam is emitted in frequent bursts rather
than continuously. The pressure generated will cause a burst noise. This is normal. As this steam is so powerful and concentrated,
you may opt not to keep the steam on the maximum setting. If you choose to keep it on maximum, more frequent filling will be necessary. To set the intra steam level, move the steam lever to the desired setting.
With the intra steam system, steam can be produced from
••temperature setting the colored position on dial to the •••
setting. Maximum steam setting should only be used when the iron is set to the highest temperature setting (•••). Steam will be produced when the iron is used horizontally.
Burst of Steam – This feature is ideal for removing stubborn wrinkles or pressing in sharp creases.
When the temperature control is set to a steam setting (•• or •••) the burst of steam can be used. Press the button to generate a burst of steam. Leave an interval of at least four seconds between bursts.
injury. |
SPECIAL INSTRUCTIONS
•This is a 1600 watt appliance. To avoid a circuit overload, do not operate a high wattage appliance on the same circuit.
•If an extension cord is absolutely necessary, the marked electrical rating should be at least as great as the electrical rating of the appliance. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over unintentionally.
•Your Rowenta appliance is intended for household use only.
SAVE THESE INSTRUCTIONS
Colour | LED display |
YELLOW
GREEN
RED
This means: | What to do |
The soleplate is | Allow iron to finish |
not hot enough. | heating. |
The soleplate is | You can start ironing |
at the right tem- | now. The soleplate is at |
perature for the | the optimum tempera- |
selected material. | ture for your material. |
The soleplate is | Wait for the iron to cool |
still too hot for | down to the selected |
the selected | temperature and the |
material. | LED display to switch |
| to GREEN. |
If you need to add water during ironing, unplug the iron and follow the steps above. Ensure iron heats back to temperature:
–indicator light turns green on models with LED Light display system
–light will go out on irons not equipped with the LED Light display system.
Water Recommendations
Tap water
Rowenta irons are designed to be used with REGULAR TAP WATER (up to 12 grains of hardness). If your water is harder than this, Rowenta recommends mixing half tap water with half distilled water which reduces the hardness; or just use bottled spring water. Never use 100 % distilled water as this can cause the iron to spit and leak.
polyester, silk, viscose
Wool
Cotton, linen
Models equipped with Electronic Temperature Control (Thermo Control)
The iron has an electronic sensor that monitors the tempe- rature of the soleplate and ensures it is accurate. The ther- mostat light will be yellow as the iron is heating. Once the correct temperature is reached the light will turn green. We recommend using the chart below as a guide to set the iron:
Vertical Steam – This feature is ideal for hanging clothes, drapes, curtains, etc.
When the temperature control is set to a steam setting vertical steam can be used. To use feature, hold iron vertically with the tip tilted forward slightly. Press the burst of steam button repeatedly while moving iron from bottom of garment to top. If vertical steam output starts to decrease tilt iron for- ward to a horizontal position and then back to vertical to continue.
Spray Setting
This feature is ideal for stubborn wrinkles or set in creases. Ensure there is water in the tank then press the spray button. Do not spray silk.
