Ruby Tech ES-2310Q 14,880PPS, 10Mbps, 148,800PPS, 100Mbps, Cat. 5 UTP cable, up to 100m, Up to 2Km, Single-ModeFiber, up to, 5/20/60Km, Single Fiber, BiDi 20Km, Forwarding Rate

RUB TETECH	Fast EthernetSwitch
	L2 Managed Switch

Switch Ethernet Fast

---Supports two scheduling, WRR and Strict

---Supports priority in a Q-in-Q tag

Bandwidth Control

---Supports bandwidth rating per port ingress and egress rate limit 1000Mbps with 1Mbps increment

Broadcast Storm

---Multicast/Broadcast/Unknown-Unicast Storm suppression.

Transmission Mode

---10/100Mbps support full or half duplex

Transmission Speed

---10/100Mbps for TP and 100Mbps for Fiber

Port Mirroring

---Support 1: N RX port mirroring

---Supports port sniffer function with 3 modes:

(TX Monitor Mode, RX Monitor Mode and TX-RX pair Monitor Mode)

Isolated Group

---Provide one group allows certain ports to be designated as protected

Restricted Group

---Can decide the direction of transmitting packets for the specific port

Protocol

LACP

---2 Fast Ethernet +1 Gigabit Ethernet groups

---Per-group max 4 member

---Provides DA, SA and DA+SA Mac- based trunking with automatic link fail- over

GVRP/GARP

---802.1q with GVRP/ GARP

Multicasting

---Supports IGMP snooping including active and passive mode

STP/RSTP

---802.1d/1w

Network Security

---802.1x access control

---Isolated group

---Restricted group

---Management Access Policy Control

---Static mac, to limit which mac addresses can pass through or not

---Mac addresses learning limit, to set up the maximum amount of mac that each port can learn

Snmpv1,v2c Network Management

RFC 1213 MIB (MIB-II)

Interface MIB

Address Translation MIB

IP MIB

ICMP MIB

TCP MIB

UDP MIB

SNMP MIB

Broadcast/Multicast/unknown-unicast Storm Control

To limit too many broadcast/multicast/unknown-unicast flooding in the network, broadcast/multicast storm control is used to restrict excess traffic. Threshold values are available to control the rate limit for each port. Packets are discarded if the count exceeds the configured upper threshold.

Technical Specifications

LED Description

		LED	Color		Function
Global	POWER		Green		-Lit when +5V power is coming up
Global	CPU		Green		-Blinks when CPU is active
Port	LINK/ACT		Green		-Lit when connection with remote device
1-8					is good
					-Blinks when any traffic is present
Port	10/100		Green		-Lit Green when TP link on 1000Mbps
1-8	Mbps		/Amber		speed
					-Off when 10Mbps or no link occurs
Port	SEP		Green		- Lit when SEP connection with remote
9,10					device is good
					-Blinks when any traffic is present
Network Interface
Category		Connector		Transmission		Max. Cable	Wavelength
						Length
10-T/		RJ-45		Full/Half Duplex		100M	/
100-TX
100-FX		SC/ST		Full/Half Duplex		2Km	1310nm
(M-M)						50/125ì
100-FX		SC		Full/Half Duplex		5/20/60Km	1310nm
(S-M)						9/125ì
100-FX		Bidi-SC		Full/Half Duplex		20Km	1310nm
(S-M)						9/125ì	1550nm

Full Forwarding Packet Rate: PPS (64 Bytes packets per second)

Forwarding Rate			Speed
14,880PPS			10Mbps
148,800PPS			100Mbps
Cable and Maximum Length
Feature		Detailed Description
TP		Cat. 5 UTP cable, up to 100m
100Base-FX SC/ST M-M		Up to 2Km
100Base-FX SC S-M		Single-Mode Fiber, up to
		5/20/60Km
100Base-FX WDM SC S-M		Single Fiber, BiDi 20Km
Hardware Spec
Feature			Detailed Description
Voltage	100~240 VAC
Frequency	50~60 Hz
Consumption	8.9W
Ambient Temperature	0 to 40 C
Humidity	5% to 90%
Dimensions	44(H) x 220(W) x 130.5(D) mm
Safety	Comply with FCC Part 15 Class A & CE
	Mark Approval