Ruby Tech PSES-2126C Technical Specifications, QoS, System LED, Rate Limit, Port Mirroring, Isolated Group, LED Description, Broadcast Storm, Restricted Group, Restricted Group

Switch Gigabit

R

RUB TECHTECH

Networking & Communications						Gigabit Switch
						L2 Managed PoE Switch
---IEEE802.1q tag-base VLAN, 4094		transmission and reception of packets can be guaranteed in event of any fail-
max, up to 256 active VLANs included		over switch on the network.
static plus dynamic entry		2 Dual Media for Flexible Fiber Connection
---IEEE802.1q tag-base VLAN		Dual media port 25 and 26 are provided for flexible fiber connection. You can
---Flooding unknown vlan frame setting,		select to install optional transceiver modules in these slots for short, medium
can flood packet with some vlan tag		or long distance fiber backbone attachment. Use of the SFP will disable their
associated to a invalid/inactive vlan		corresponding built-in 10/100/1000Base-T connections.
---In tag-base VLAN, supports egress/		Broadcast/Multicast/Unknown-unicast Storm Control
ingress packet filter		To limit too many broadcast/multicast/unknown-unicast flooding in the network,
---Q-in-Q is an efficient method for		broadcast/multicast storm control is used to restrict excess traffic. Threshold
enabling Subscriber Aggregation.		values are available to control the rate limit for each port. Packets are
QoS
		discarded if the count exceeds the configured upper threshold.
---Port Based (VIP Port), 802.1p , TOS
and Diffserv(IPv4/IPv6) based QoS	Technical Specifications
packet classification
		LED Description
---Supports four level priority queues to
prioritize in-bound and out-bound		LED	Color			Function
traffic					System LED
---Supports two scheduling, WRR and		CPURUN	Green	-Blinks when CPU is on and good
Strict		POWER	Green	-Lit when AC power is on and good
---Supports priority in a Q-in-Q tag		ACT	Green	-Lit when LEDSET set on active mode
Broadcast Storm		FDX	Green	-Lit when LEDSET set on full-duplex mode
---Multicast/Broadcast/Unknown-Unicast		SPD	Green	-Lit when LEDSET set on speed mode
Storm suppression.			10/100Mbps Ethernet TP Port 1 to 24 LED
Port Mirroring		LNK	Green	-Lit when connection with remote device is good
---Support 1: N RX port mirroring.				-Off when cable connection is not good
---Supports port sniffer function with 3		ACT/FDX	Amber	(a)LEDSET set on ACT (active) mode:
modes:
		/ SPD	(TP Port		-Blinks when any traffic is present
(TX Monitor Mode, RX Monitor Mode
			1 to 24	(b)LEDSET set on FDX (full-duplex) mode:
and TX-RX pair Monitor Mode).
			LED)		-Lit when full-duplex mode is active
Isolated Group
					-Blinks when any collision is present
---Provide one group allows certain
				(c)LEDSET set on SPD (speed) mode:
ports to be designated as protected.
					-Lit when 100Mbps speed is active
Restricted Group
					-Off when 10Mbps speed is active
---Can decide the direction of
		10/100/1000Mbps Gigabit TP/Fiber Port 25, 26 LED
transmitting packets for the specific
port		LNK	Green	-Lit when connection with remote device is good
Restricted Group				-Off when cable connection is not good
---Can decide the direction of tran		FX	Green	-Lit when Fiber port is active
smitting packets for the specific port				-Off when TP port is active
Rate Limit		ACT/FDX	Green	(a)LEDSET set on ACT (active) mode:
---Ingress rate limit:		/ SPD	(Port 25,		-Blinks when any traffic is present
Port 1~24: 1K up to 100Mbps			26 LED)	(b)LEDSET set on FDX (full-duplex) mode:
Port 25, 26: 1K up to 1000Mbps					-Lit when full-duplex mode is active
---Egress rate limit:					-Blinks when any collision is present
Port 1~24: 1K up to 100Mbps				(c)LEDSET set on SPD (speed) mode:
Port 25, 26: 1K up to 1000Mbps					-Lit when 1000Mbps speed is active
PoE Specification
					-Off when 10/100Mbps speed is active
---24 IEEE802.3af PoE PSE ports
			PoE Port Status Indication LEDs
---Endpoint with 48VDC power through
		PoE-PSE	Green	-Lit when PoE Power is active
RJ-45 pin 1, 2, 3, 6.
		ACT
---PoE-PSE activity LED indicator.
---185 watts of total power (up to 15.4		Cable and Maximum Length:
watts for 12 ports, or up to 7.7 watts
		TP				Cat. 5 UTP cable, up to 100m
for 24 ports)
---Auto detect powered device and		1000Base-SX SC M-M				Up to 220/275/500/550m,
consumption levels						which depends on Multi-Mode Fiber type
---Supports per port power consumption
		1000Base-LX SC S-M				Single-Mode Fiber, up to10/30/50Km
monitoring
		1000Base-LX WDM SC S-M				Single-Mode Single Fiber, Bidi 20Km
---Smart feature for PD on/off, PD
detection, power level, PD status and
power feeding priority
---Circuit protection to prevent power
interference between ports
---Supports per port PoE State setting