Manuals / Ryobi / Lawn and Garden / Trimmer

Ryobi CS30 RY30220 Starting And Stopping, Operation, Start Position, Run Position, See Figures

Models: BC30 RY30260 SS30 RY30240 CS30 RY30220

1 26

Download 26 pages 7.53 Kb

Page 18

Image 18

OPERATION

STARTING AND STOPPING

See Figures 21 - 23.

TO START A COLD ENGINE:

DO NOT squeeze the throttle trigger until the engine starts and runs.

Lay the trimmer on a flat, bare surface.

PRIME - Press the primer bulb 7 times.

SET the start lever to the START position.

PULL the rope until the engine starts.

Wait 6-10 seconds, then squeeze the trigger to run.

NOTE: Squeezing the throttle trigger releases the start lever to the RUN position.

TO START A WARM ENGINE: PULL the rope until the engine starts.

TO STOP THE ENGINE:

Press and hold the switch in the stop “ ” position until the engine stops.

IGNITION

SWITCH

TRIGGER

LOCK

THROTTLE

TRIGGER

Fig. 21

PRIMER BULB

IGNITION

SWITCH

TRIGGER LOCK

THROTTLE TRIGGER

Fig. 22

START POSITION

START LEVER

RUN POSITION

START LEVER

Fig. 23

Page 18

Image 18

Ryobi CS30 RY30220 Starting And Stopping, Operation, Start Position, Run Position, See Figures, To Start A Cold Engine

Contents

SAVE THIS MANUAL FOR FUTURE REFERENCE OPERATOR’S MANUAL30cc String Trimmers and Brushcutters SS30 RY30240 CS30 RY30220 BC30 RY30260INTRODUCTION TABLE OF CONTENTSGENERAL SAFETY RULES READ ALL INSTRUCTIONSSPECIFIC SAFETY RULES SPECIFIC SAFETY RULES FOR TRIMMER USESPECIFIC SAFETY RULES FOR BRUSH- CUTTER AND BLADE USE NAME SYMBOLSSYMBOL EXPLANATIONSYMBOLS SERVICESAVE THESE INSTRUCTIONS SYMBOL SIGNALPRODUCT SPECIFICATIONS FEATURESCS30 Weight - without fuelSS30 FEATURESDRIVE SHAFT HOUSING KNOB BLADE SHOULDER HARNESS BRUSHCUTTER GUARD BC30GRASS DEFLECTOR ASSEMBLYKNOW YOUR STRING TRIMMER TOP-MOUNTED MOTORATTACHING THE STORAGE HANGER INSTALLING THE POWER HEAD TO THE ATTACHMENTREMOVING THE ATTACHMENT FROM THE POWER HEAD ASSEMBLYASSEMBLY ATTACHING THE FRONT HANDLE - CS30 AND SS30ATTACHING THE “J” HANDLE - BC30 See FigureTO ATTACH THE STRAIGHT SHAFT GRASS DEFLECTOR - SS30 ATTACHING THE GRASS DEFLECTORTO ATTACH THE CURVED SHAFT GRASS DEFLECTOR - CS30 ATTACHING THE BRUSHCUTTER GUARD - BC30CONVERTING FROM BRUSHCUTTER TO STRING TRIMMER - BC30 INSTALLING THE STRAIGHT SHAFT GRASS DEFLECTOR AND STRING HEADATTACHING THE SHOULDER HARNESS - BC30 REMOVING THE TRI-ARC BLADE AND BRUSHCUTTER GUARDREMOVING THE STRAIGHT SHAFT GRASS DEFLECTOR AND STRING HEAD INSTALLING THE TRI-ARC BLADE AND BRUSHCUTTER GUARDOPERATION ASSEMBLYOPERATION FUELING AND REFUELING THE TRIMMEROPERATING THE TRIMMER FUEL MIXTURECUTTING TIPS TO ADVANCE THE CUTTING LINETO ADVANCE THE CUTTING LINE MANUALLY GRASS DEFLECTOR LINE TRIMMING CUT-OFF BLADETRI-ARC BLADE OPERATING THE BRUSHCUTTERBLADE THRUST CUTTING TECHNIQUE - BLADEPRIMER BULB IGNITION SWITCH TRIGGER LOCK THROTTLE TRIGGER STARTING AND STOPPINGIGNITION SWITCH TRIGGER LOCK THROTTLE TRIGGER OPERATIONSPOOL REPLACEMENT MAINTENANCEGENERAL MAINTENANCE NEW PREWOUND SPOOLTo install the spool retainer STRING REPLACEMENTMAINTENANCE See Figures 26SPARK PLUG REPLACEMENT CLEANING THE EXHAUST PORT AND MUFFLERREPLACING AND CLEANING AIR FILTER SPARK ARRESTORSOLUTION TROUBLESHOOTINGPROBLEM POSSIBLE CAUSETROUBLESHOOTING WARRANTYTHIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER PROBLEMLIMITED WARRANTY STATEMENT WARRANTYTECHTRONIC INDUSTRIES NORTH AMERICA, INC., LIMITED WARRANTY WARRANTYOPERATOR’S MANUAL SERVICEHOW TO ORDER REPAIR PARTS 30cc String Trimmers and Brushcutters