The purpose of safety symbols is to attract your atten- tion to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by them- selves eliminate any danger. The instructions or warnings they give are not substitutes for proper acci- dent prevention measures.
SYMBOL MEANING
SAFETY ALERT SYMBOL: Indicates dan-
ger, warning, or caution. Attention is required in order to avoid serious personal injury. May be used in conjunction with other symbols or pictographs.
NOTE: Advises you of information or instructions vital to the operation or maintenance of the equipment.
_
_L
DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock, and
personal injury.
ARNING: Failure to obey a safety warning
can result in injury to yourself and others. Always follow the safety precautions to reduce the risk of fire, electric shock, and
personal injury.
may result in property damage or personal injury to yourself or to others. Always follow
the safety precautions to reduce the risk of AUTION: Failure to obey a safety warning
fire, electric shock, and personal injury.
• IMPORTANT SAFETY INFORMATION •
READ ALL INSTRUCTIONS BEFORE
OPERATING
•Read the instructions carefully. Be familiar with the controls and proper use of the unit.
•Do not operate this unit when tired, ill, or under the influence of alcohol, drugs, or medication.
•Children and teens under the age of 15 must not use the unit, except for teens guided by an adult.
•Inspect the unit before use. Replace damaged parts. Check for fuel leaks. Make sure all fasteners are in place and secure. Replace cutting attachment parts that are cracked, chipped, or damaged in any way. Make sure the cutting attachment is properly installed and securely fastened. Be sure the cutting attachment shield is properly attached, and positioned as recommended. Failure to so can result in personal injury to the operator and bystanders, as well as damage to the unit
•Use only 0.095 inch (2.41 mm) diameter genuine Ryobi replacement line. Never use
•Be aware of the risk of injury to the head, hands and feet.
•Clear the area to be cut before each use. Remove all
objects such as rocks, broken glass, nails, wire, or string which can be thrown or become entangled in the cutting attachment. Clear the area of children, bystanders, and pets. At a minimum, keep all children, bystanders and pets outside a 50 ft. (15 m.) radius; there still may be a risk to bystanders from thrown objects. Bystanders should be encouraged to wear eye protection. If you are approached, stop the engine and cutting attachment immediately.
•Squeeze the throttle control and check that it returns automatically to the neutral position. Make all adjustments or repairs before using unit.
SAFETY WARNINGS FOR GAS TRIMMERS
and its vapors can explode if ignited. Take
_ARNING: Gasoline is highly flammable, the following precautions:
•Store fuel only in containers specifically designed and approved for the storage of such materials.
•Avoid creating a source of ignition for spilled fuel. Do not start the engine until fuel vapors dissipate.
Always stop the engine and allow it to cool before filling the fuel tank. Never remove the cap of the fuel tank, or add fuel, when the engine is hot. Never operate the unit without the fuel cap securely in place. Loosen the fuel tank cap slowly to relieve any pressure in the tank.
Mix and add fuel in a clean,
Move the unit at least 30 ft. (9.1 m) from the fueling source and site before starting the engine. Do not smoke, keep sparks and open flames from the area while adding fuel or operating the unit.
WHILE OPERATING
•Never start or run the unit inside a closed room or
building. Breathing exhaust fumes can kill. Operate this unit only in a well ventilated area outdoors.
Wear safety glasses or goggles that are marked as meeting ANSI
The cutting attachment shield must always be in place while operating the unit as a trimmer. Do not operate unit without both trimming lines extended, and the proper line installed. Do not extend the trimming line beyond the length of the shield.
