Samson MDR 16 specifications Mdr, ARCHITECT’S & ENGINEER’S Specifications, Maximum Voltage Gain

PRODUCT SPECIFICATION SHEET

	SERIES	DESCRIPTION	CATEGORY
	MDR	MIXER	MIXERS
FEATURES (continued)			MDR 16 SPECIFICATIONS

MDR 16

>2 TK TO MIX control allows you to mix in a CD, DAT, Cassette, Computer Sound Card or Mini Disk.

>The mono inputs feature a three-band channel equalizer with 15dB of cut or boost at 80Hz, variable mid-range from 100 Hz to 5 KHz with 15dB of cut or boost and 15dB of cut or boost at 12KHz, plus a Low Cut filter at 80Hz.

>Two Auxiliary Sends, with Pre-Post switching on Aux 1, can be used to route signals to external effects, or to create a separate mix for on-stage monitors, or studio headphones.

>Twelve-segment LED Meter, with VU ballistics, displays the main MIX output, plus SOLO, PFL, Phantom and Power LED indicators.

>High quality, low noise, discrete microphone pre-amplifiers, with 48-Volt phantom power, provide Maximum Dynamic Range and transparent audio.

>Advanced circuit design using discrete components and high quality, low noise op-amps carefully selected at each stage of the signal path.

>Quality build and rugged construction ensure reliable performance from venue to venue and session to session.

>Three-year extended warranty.

95mm

413mm

578mm

ARCHITECT’S & ENGINEER’S SPECIFICATIONS

The Samson MDR16 shall be a 16 input, 4 bus stereo output mixer. It shall have 8 mic channels with trim control, HF Level control, High pass switch, MF level and frequency sweep, LF Level control, 2 aux sends (one pre / post switchable), pan control, solo button, bus 1-2 switch, bus 3-4 switch and a 60mm fader. It shall have 8 mic/line channels with High frequency control, low frequency control, 1 aux control with aux 1/2 switch, pan control,solo button, bus 1-2 switch, bus 3-4 switch and 60mm fader. 60mm bus 1, 2, 3, and 4 and left and right output faders will also be available. A control room and headphone output with level control shall also be provided. 24 bit, DSP effects shall also be provided with 8 presets. A nine band graphic equalizer is also available in the master section with the ability to equalize the main mix or the aux 1 mix. The MDR16 uses an external power supply.

Frequency Response (Trim @ Min, unity gain +0 / -1 dB)

Mic to Main	10 Hz - 30 kHz
Line to Main	10 Hz - 30 kHz
Aux Return to Main	10 Hz - 30 kHz
Line to Aux Send	10 Hz - 32 kHz

T.H.D. (Trim @ Min, +4dBu output, unity gain, 1 kHz w/30 kHz LPF) Mic/Line to Main (Mono Ch). 0.02%

Line to Main (Stereo Ch)	0.02%
Line to Aux Send	0.02%
Equivalent Input Noise ("A" filter on, input shorted)
Mic	-128 dB
Line	-103 dB
Maximum Voltage Gain
Mic to Main	72 dB
Line to Main (Mono Ch)	56 dB
Line/Tape to Main (Stereo Ch) 20 dB
Aux Return to Main	20 dB
Mic to Aux Send	74 dB
Line to Aux Send (Stereo Ch) . 41 dB
Residual Noise (30 kHz LPF, all control Min)
Main	-85 dBu
Aux Send	-82 dBu
Crosstalk (@ 1 kHz w/ 30 kHz LPF)
Ch vs. Ch	-75 dB
Input vs. Output	-86 dB
Peak LED Sensitivity (before clipping)....	5 dB
CLIP Indicators	Turn on: THD> 0.1%
Headphone output (600 ohm load)	100 mW
Maximum Input Level (1 kHz, Ch. & Mix fader set to zero)
Mic Input (Mono Ch)	+11 dBu
Line Input (Mono Ch)	+27 dBu
Input Channel Equalizer (± 2dB)
High (shelving)	12 kHz ±15 dB
Mid (peaking)	Variable 100Hz - 5 kHz ± 15 dB
Low (shelving)	80 Hz ±15 dB
Meters	12 POINT LED METERS (-21,
	-18, -16, -12, -8, -6, -3, 0,
	+3, +6, +9, +20) PEAK
Internal DSP Effects	24 BIT -8 presets: 1 - Large
	Hall; 2 - Medium Hall, 3- Large
	Room; 4 - Vocal Room 1;
	5 - Vocal Room 2; 6 - Chorus +
	Reverb; 7 - Chorus + Delay;
	8 - Stairwel
Phantom Power	+48V
Power Requirement	110V-240V, 50/60Hz
Power Consumption	50W
Dimensions (W x D x H)	22.75” x 16.25” x 3.75”
	(578mm x 413mm x 95mm)
Weight	17.5 lbs. (8 kg )