Samsung 49-2516 owner manual #/4#/1706+07+&.+05, 1706+0#0&+056#..+06*%#/4#, 566+0726*%#/4#

315/+PEJ"%QNQT"+PFQQT11WVFQQT"%COGTC

www.radioshack.com™

OWNER’S MANUAL —		49-2516
Please read before using this equipment.
Thanks for purchasing a RadioShack	Built-in Speaker and Microphone — allow	CMOS (Complementary Metal-Oxide
1/3-InchColor Indoor/Outdoor Camera. Your	2-way communication with compatible	Semiconductor) Sensor — provides
camera is super-small and compact. It is	equipment.	superior-resolution color and B&W images.
designed for use with a RadioShack 10-Inch	Color-B&W Auto Switching — enables	Passive Infrared (PIR) Sensor — detects
Single Channel Security Monitor (Cat. No.
	better night vision by automatically turning to	motion up to 16.5 feet away from an angle of
49-2514) to provide a safe and secure
	B&W when illumination falls below 2 Lux.	up to 100°.
environment.
		Weatherproof — so you can mount the
		camera indoors or outdoors.

%#/'4#"/1706+0)")7+&'.+0'5

Carefully plan where and how you will position the camera and where you will route the cable that connects the camera to the monitor. When planning the installation:

±"016'"±"

Though the camera is highly sensitive, it cannot “see” over a wide area in total darkness. To assist the camera’s night vision, install a 100-watt incandescent lamp (rich in infrared radiation) to illuminate the camera’s viewing area. You can also use a small incandescent flood lamp. Halogen lamps, other high pressure outdoor lamps, and fluorescent lighting are infrared-poor and not recommended.

•Select a location for the camera that provides a clear view of the area you want to monitor, is free from dust, and is not in direct sunlight or in line-of-sight of a strong light source.

•Do not install the camera in a location where it will be exposed to high humidity or rain.

•Plan the cable’s route so it is not close to power or telephone lines, transformers, microwave ovens, or other electrical equipment that could interfere with (or accept interference from) the system.

•Select a location for the camera that has an ambient temperature between –4°F (–20°C) and 122°F (50°C).

•If you plan to install the camera in a location that has conditions not recommended in this manual, consult with a professional installer and consider use of a separate camera cover or housing.

/1706+0)"#0&"+056#..+0)"6*'"%#/'4#

You can mount the camera indoors or outdoors in a permanent location such as a wall or on a movable platform (such as a tripod) for mounting on a desk, shelf, or table.

1.Use the base of the camera as a guide, mark the locations for the screw holes on the mounting surface.

2.Drill a starter hole at each marked location. If necessary, drill a third hole (at least 14 mm in diameter) below the mounting holes to permit the camera’s cable to be inserted through the mounting surface.

3.If necessary, insert the supplied drywall anchors into the screw holes.

4.Insert one of the two supplied screws through each of the screw holes in the bracket and into the mounting surface, then tighten each screw until the base is secure.

5.Loosen the screw from the camera’s arm-sleeve and fully insert the base’s arm into the sleeve. Then secure the

arm and sleeve together by tightening the screw.

5'66+0)"72"6*'"%#/'4#

%100'%6+0)"&+4'%6.;"61"6*'" /10+614

1.Connect the camera’s mini-DIN plug into the supplied 59-foot cable’s mini-DIN

socket.

2.Connect the 59-foot cable to the monitor’s mini-DIN port.

		#"+/2146#06"#			© 2002 RadioShack Corporation.
If an icon appears at the end of a paragraph, go to the box on that page with the corresponding icon for					All Rights Reserved.
					RadioShack and RadioShack.com are trademarks
pertinent information.
					used by RadioShack Corporation.
Rý— Warning	# — Important	±— Note	.— Caution	° — Hint