SCW-230(E/G/F/S) 3/31/00 2:35 PM Page 3

System Requirements

Before you install the CD-R/RW drive, we strongly recommend that you make certain that your set-up meets the system requirements listed below.

Item

Description

Type of computer

Pentium 75MHz(or higher) with an IDE interface

RAM

16MB RAM(or higher)

Hard drive

528MB higher(Transfer Rate 800KB/sec higher Access,

 

Time 20m/sec Lower)

MS-DOS

5.0(or higher)

 

TIP:For MS-DOS, The CD-R/RW drive can only Read a

 

disc without Premaster Software

Windows

Microsoft® Windows 95® or Windows NT 4.0®

 

TIP:For Windows NT®, we recommend Service Pack2,

 

Version 4.00.1381.

Installing the CD-R/RW Drive

Install the CD-R/RW drive in your computer horizontally, making sure that the Open/Close button is on the right.

To install the drive, proceed as follows.

1 Turn OFF your computer. Remember to verify the configuration jumper on the rear of the CD-R/RW drive.

2 Remove the cover of your PC(main unit of the computer).

3 Remove the blank cover panel of the 5.25 inch unit in which the CD-R/RW drive is to be installed.

4 Connect the CD-R/RW drive to the IDE interface and power cables located inside your computer.

Connectors are keyed so it is impossible to put them in

an incorrect position. Do not force the connectors, if they

do not seem to fit.

5 Install the CD-R/RW drive into the unit and secure it with mounting screws (recommended standard M3x6).

Depending on your PC model, you may need to attach

guide rails to the drive, so that the drive is held firmly in place.

On the ground that the guide rails are parts of the computer,

☛ ◆ if you don’t have these, please purchase separately.

If you use screws that are longer than the recommended

☛ ◆ standard, you may damage the drive.

6 Put the cover back on your PC.

Installing the Device Driver

You can install the device driver for DOS or for Windows.

TIP : You can use the CD-R/RW drive to only read a disc in DOS/Windows 3.1.

1

Turn on your computer and wait for it to boot.

 

English

3

DOS user

Type a: at the DOS prompt.

2

Insert the driver disk into a floppy disk drive (usually the A drive).

 

 

If you are a...

Then...

 

 

 

 

Press the RETURN key.

 

 

 

 

 

 

 

Windows user

Access the File Manager.

 

 

3.1

Click on the A icon.

 

 

 

Windows 95 user

When you are in Windows 95, it is not

 

 

/NT 4.0

necessary to install Device Driver.

 

 

 

Whereas, when you are in Dos Mode of

 

 

 

Windows 95, then install as follows.

 

 

 

Click on MY COMPUTER icon.

 

 

 

Click on the A icon.

 

 

 

 

 

4

Run the CDSETUP program:

 

 

 

If you are a...

Then...

 

 

 

 

 

 

 

DOS user

Type CDSETUP after the a: prompt.

 

 

 

Press RETURN.

 

 

 

 

 

 

 

Windows user

Double-click CDSETUP.EXE from the

 

 

3.1

Windows File Manager.

 

 

 

 

 

 

5

To...

Then enter...

 

 

 

Confirm the installation

Y

 

 

 

 

 

 

 

Exit without installing

N

 

 

 

 

 

 

Result: If you answer Y(Yes), the installation program automatically

 

 

Creates a SAMSUNG directory on your hard disk

 

 

Copies the required softwares (mscdex.exe and sscdrom.sys)

 

 

Modifies the CONFIG.SYS and AUTOEXEC.BAT files

 

 

 

 

 

6

When the Setup Completed screen is displayed, remove the installation

 

 

floppy disk from the drive.

 

 

 

7

Reboot your system.

 

 

 

 

Result: The computer restarts

 

 

Both the device driver and MSCDEX are loaded.

 

4

5

Page 3
Image 3
Samsung SCW-230 warranty System Requirements, Installing the CD-R/RW Drive, Installing the Device Driver