INSTALLATION & MAINTENANCE

ENVIRONMENT

Leave some space

Maintain at least 10cm between the washer and the wall.

Place the washer on a sturdy flat surface.

If the washer is placed on an uneven or weak surface, noise or vibration occurs. (Allowable is 1 )

Adjust the legs for even placement. Never install the washer near water.

ASSEMBLING THE SOUND ABSORBING PANEL

Tilt the washer a little and lift up the panel until it clicks,

filnaly fix the panel with screw to the base as shown in the figure.

Rear-side

CLEANING THE FILTER NET

1.Push the upper part of

2.Open the cover as

3.Clean the filter.

4. Close the cover and insert the lower

the filter and pull in.

shown in the figure.

 

part of the filter in the basket first and

 

 

 

then push the filter with "click" sound .

Do not place the washer in steamy rooms or where the washer is directly exposed to rain.Moisture may destroy the electrical insulation causing an electrical shock hazard.

Avoid direct sunlight or heaters.

As plastic and electrical components are affected by direct heat,never place the washer near furnaces, boilers,etc.Do not place under direct sunlight.

IN CASE OF PUMP-DRAINED WASHER

Take out the

Be sure to join tightly

Install the drain

cap-hose and

the drain hose into the

hose in the position

connect the

drain-outlet on theback

of about 70~80cm

outlet-hose.

of the machine.

above the ground.

cap-hose

outlet-hose

CONNECTING THE DRAIN HOSE

After pressing the joint ring(a), insert the drain hose(b) to drain direction. (a)

(b)

LEVELLING

SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING THE POSITION OF THE WASHING TUB.

Open the lid of the machine, pour water into the tub up to the level just below the pulsator, and adjust the legs so that the pulsator is positioned at the center of the water as shown in the figure. Place the machine more than 10cm away from the wall.

HOW TO ADD THE FABRIC SOFTENER

When a proper amount (one time does) of fabric softener is stored in the softener inlet,it is automatically put in at the last rinsing cycle.

Do not use detergent, bleach or starch into the Softener Inlet.

Using too much softener may produce unsatisfactory results.

Do not open the lid during the Spin Dry cycle. If added too early, its effectiveness

will decrease.

Do not leave the softener into the Softener Dispenser for a long time.

Because softner became stiff.

Pour it slowly

IN CASE OF COLD-HOT WATER WASHER

If you use only cold

 

water inlet hose, you

Hot

must fit the cap to the

Cold

hot water inlet valve

 

as following.

cap

 

HOW TO CLEAN THE FILTER

HOW TO PUT THE DETERGENT IN

Adjust the legs on feet for levelling . Loosen Lock

CONNECTING THE WATER SUPPLY HOSE

1.Remove the adaptor

4.Connect the water supply

from the water

hose to the adaptor. Pull down

supply hose.

the part (c) of the water supply

 

hose .When the part (c)is released,

 

the hose is automatically

 

connected to the adaptor

 

making a 'click' sound.

2.First,using a "+" type

5.Connect the other end of

1. Place a rag under the washer filter not to wet the floor.

2. Rotate the filter counterclockwise and pull out the filter.

3. Remove dirts and rotate the filter clockwise until it locks in position.

1.Open the detergent box by pulling in the direction of the arrow as shown in the figure and then put the powder detergent in the detergent box.

2.Put in one-time amount

of detergent evenly so the detergent may

not brim over the box.

screw driver, loosen the

the water supply hose to

four screws on the adaptor.

the inlet water valve at the

Next,take the adaptor and

back of the washer.

turn part(b) following the

Screw the hose clockwise

arrow for gap about 5mm

all the way in.

between them.

 

3.Connect adaptor to the

If the water tap is a screw

water tap by tightening

type,assemble a water

the screws firmly.

supply hose that fits to the

Then,turn part (b)

tap as shown.

following the arrow and

 

put (a) and (b)together.

 

HOW TO ASSEMBLE THE LEGS

1. Check the 4 Legs.(Front-right. Front-left. Rear-right. Rear-left)

Hook

2. Lay down the Washing Machine to the front.

 

Hole

3. Insert the hook of leg in to the square hole of base.

 

 

 

4.Push the leg to the arrow direction to “Click”.

2

 

5.Finaly fix the legs on the base with screw like a figure.

1

 

Base

Screw

NOTICE After completing connection,if water leaks from the hose,then repeat the same steps. Use the most conventional type of faucet for water supply.

In case the faucet is square or too big,remove the spacing ring before inserting the faucet into the adaptor.

7

8