INFORMATION TO USER
PRECAUTIONS
INSTRUCTION MANUAL |
|
(Warranty attached)
COLOR CCD cameraAbout this manualBefore installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.
Dimensions: mm
67 |
| 136 |
|
|
|
1126.5
54
Safety Guard
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT.
WARNING:TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
For the customers in CanadaThis Class B digital apparatus complies with Canadian
Cet appareil numerique de la Classe B est conforme a la norme
This installation should be made by a qualified service person and should conform to all local codes.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
In case of problem
Do not use the camera if smoke or strange odors come from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer or a Sanyo Authorized Service Center.
Do not open or modify
Do not open the cabinet, as it may be dangerous and cause damage to the unit. For internal settings and repairs, consult your dealer or a Sanyo Authorized Service Center.
Do not put objects inside the unit
Make sure that no metal objects or flammable substances get inside the camera. If used with a foreign object inside, it could cause fire,
Be careful when handling the unit
To prevent damage, do not drop the camera or subject it to strong shock or vibration.
Protect from high temperatures
Do not install close to stoves, or other heat generating devices, such as spotlights, etc., or where it could be subject to direct sunlight, as that could cause deformation, discoloration or other damage.
Be careful when installing close to the ceiling, in a kitchen or boiler room, as the temperature may raise to high levels. Install where the temperature range will stay between
Cleaning
Dirt can be removed from the cabinet by wiping it with a soft cloth. To remove stains, use a soft cloth moistened with a soft detergent solution and wrung dry, then dry by wiping with a soft dry cloth.
Do not use benzine, thinner or other chemical products on the cabinet, as they may cause deformation and paint peeling. Before using a chemical cloth, make sure to read all accompanying instructions. Make sure that no plastic or rubber material comes in contact with the cabinet for extended periods, as that may cause damage or paint peeling.
11
28 | 15.4 |
|
|
25.2
Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer.
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by Sanyo may void the user's authority to operate this camera.
Install away from electric or magnetic fields
If installed close to a TV, radio transmitter, magnet, electric motor, transformer, or audio speakers, the magnetic field they generate will distort the image.
Protect from humidity and dust
To prevent damage to the camera, do not install it where there is |
|
greasy smoke or steam, where the humidity may get too high, or |
|
where there is a lot of dust. | Printed on recycled paper |
| |
| |
| L5AN4/US |
Printed in Japan
NAMES AND FUNCTIONS OF PARTS
| |
| |
| Lens cap |
| Protects the lens from damage. |
G C B | Camera installation bracket |
| The bracket can be secured at the top or bottom of the camera. When |
| securing the bracket, use the long screws and use the short screws on the |
| opposite side to seal the openings. |
| c Short screws: M3 x 4 |
| d Long screws: M3 x 6 |
| e Camera mounting screw hole: |
TROUBLESHOOTING
Before sending the camera out for repair, check the items below. If the problem persists after checking these items, contact your place of purchase or a Sanyo Authorized Service Center.
If no image appears
Is the coaxial cable attached securely? Are the power and voltage normal?
Has the iris of the lens inside the camera been adjusted correctly (with the iris dial)?
Is there adequate illumination?
If the image is unclear
SPECIFICATIONS
Scanning system | : NTSC standard TV system | |
| (525 TV lines, 30 frames/sec.) | |
Interlace | : PLL 2:1 interlace | |
Image device | : 1/4 inch solid state image device CCD | |
Picture elements | : 537 (H) x 505 (V) | |
Effective picture | : 510 | (H) x 492 (V) |
elements |
|
|
Synchronizing system : Internal sync, Line lock manually switchable | ||
Resolution | : 350 | TV lines horizontally (color mode), |
| 380 | TV lines horizontally (B/W mode), |
| 350 | TV lines vertically |
Video output level | : 1.0 | |
Video S/N ratio | : More than 48 dB | |
Minimum required | : Approx. 0.05 lux with a F 1.2 lens (B/W mode), | |
illumination | Approx. 0.9 lux with a F 1.2 lens (color mode), | |
POWER (power indicator)Lights when the camera power is ON.
VIDEO OUT (video output terminal: BNC connector)Connects to the VIDEO IN (video input) terminal on the VCR or monitor.
CONTROL (Manual color/black and white setting terminal) G (ground) terminalC (color) terminal
B (black and white) terminal
LINE PHASE (Line phase adjustment volume)When using two cameras or more, the image on the monitor may roll vertically when switching sources. This rolling can be minimized by turning this volume.
GND, AC24V, DC12V (ground terminal, 24V AC or 12V DC input terminal)
Camera adjustment/setting panelContains camera adjustment dials and setting switches.
LENS (lens iris output terminal)Used to connect the lens plug when the lens is attached.
c Brake coil | d Brake coil (+) |
e Drive coil (+) | f Drive coil |
When installing the camera support, select a location that can support the total weight of the camera and accessories.
Attaching the lens
Use a DC type
Do not use a lens if length “L” is more than 5 mm. Otherwise, it may damage the camera and prevent proper installation.
When attaching a C mount lens, attach the lens to the camera after inserting the C mount ring (option).
1 |
| L |
| Remove the lens mount | 2 | |
2 | cap from the camera. | |
| Install the |
| |
3 | Connect the lens plug to 3 | 1 |
| the lens iris output |
|
| connector (LENS) on the | CS mount type lens |
| side of the camera. |
Is the lens in focus? Is the lens dirty?
Dirt or fingerprints on the lens can adversely affect the image. Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid (commercially available). Is the monitor adjusted correctly?
SERVICE
The camera is a precision instrument. Handle it carefully and always follow the safety precautions. If the camera requires service, never try to repair it yourself or open the casing.
For servicing, maintenance, or repairs, contact your place of purchase or a Sanyo Authorized Service Center.
(incandescent lighting) | Approx. 0.02 lux with a F 1.2 lens (B/W mode, Gain: HI) |
Day/Night | : AUTO/MANUAL (at CONTROL terminal) |
Control terminal | : Manual color/black and white setting |
Backlight | : MULTI/OFF switching |
compensation | CENT/OFF switching |
| (Active when using an |
Iris function | : EI/AI switching |
: DC output (variable DC level), | |
Electronic iris range | : 0.9 lux to 45000 lux (F 1.2 lens: color mode) |
: 12.5 mm ±0.5 mm | |
White balance | : ATW/Manual switching |
Gain up | : HI (high)/ NOR (Normal) switching |
Lens mount | : CS mount |
Environmental | : Temperature: |
conditions | Humidity: less than 90% (no condensation) |
Power supply | : 12 – 15 VDC/24 VAC, 60 Hz (±10%) |
Power consumption | : 3.2 W (with auto iris lens) |
Weight | : Approx. 430 g (without lens) |
Appearance and specifications are subject to change without prior notice.