Sanyo VCC-9684VA instruction manual Color CCD Camera, Case of a problem, Do not open or modify

English Français Español

INSTRUCTION MANUAL VCC-9684VA

Color CCD Camera

About this manual

Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.

Ceiling Installed Wall Installed

Surface routing*1 In-ceiling routing

*1 Surface routing

Cutout

Rib mark

Safety Guard

PRECAUTIONS

Important

•Be careful when opening holes for installing the unit. Work with the power and video cables pulled out for easy installation.

•Make sure to properly perform waterproofing for the ceiling or wall where you are installing the unit.

•Make sure that the surface in the installation location has no unevenness and is strong enough to bear the total weight of the unit.

•Install this unit in an environment where the temperature range stays between -10°C and +50°C/14°F and 122°F (no condensation allowed).

•As a precaution against static electricity damage, touch a nearby metal object (door knob, etc.) to dissipate static electricity in your body before touching this unit.

■In case of a problem

Do not use the unit if smoke or a strange odor comes from the unit, or if it seems not to function correctly. Turn off the power immediately and disconnect the power cord, and then consult your dealer or an Authorized Sanyo Service Center.

■Do not open or modify

Do not open the cabinet, as it may be dangerous and cause damage to the unit. For repairs, consult your dealer or an Authorized Sanyo Service Center.

■Do not put objects inside the unit

Make sure that no metal objects or flammable substance get inside the unit. If used with a foreign object inside, it could cause a fire, a short-circuit or damage. Be careful to protect the unit from rain, sea water, etc. If water or liquid gets inside the unit, turn off the power immediately and disconnect the power cord, and then consult your dealer or an Authorized Sanyo Service Center.

■Be careful when handling the unit

SPECIFICATIONS

Scanning system	: NTSC standard 525 lines, 60 fields/sec.
Image sensor	: 1/4" interline transfer method CCD
Number of effective pixels	: 768 (H) x 494 (V)
Horizontal resolution	: 540 TV lines, typical
Minimum illumination
(approx.)	: 0.5 lx (F0.95)
Video output	: 1.0 V(p-p)/75 Ω, composite, BNC
	UTP support (VA-10T: option board)
Video S/N ratio	: More than 48 dB (AGC off: More than 50 dB)
Vari-focal lens	: f=2.8 - 8 mm, F0.95 - 1.7
Rotation range	: (On the ceiling) Pan: ± 100 degrees
	Tilt: 0 - 90 degrees
	(On the wall) Pan: ± 90 degrees
	Tilt: 0 - 90 degrees
Backlight compensation	: OFF, Multi-spot metering (High/Normal), Center zone
	metering
White balance	: ATW/Manual
Electronic shutter	: 1/60, 1/100, 1/1000, 1/2000 sec.
Aperture compensation	: Sharp/Normal
Sync system	: Internal sync/Line-lock
Operating Environment	: Temperature: –10°C – +50°C (14°F – 122°F)
	Humidity: less than 90 % RH (no condensation)
Power supply	: 24 V AC ±10%, 60 Hz / 12 - 15 V DC
Power consumption
(approx.)	: 2.4 W
Weight (approx.)	: 500 g (16 oz.)
Accessory	: Screw ×1, Warranty ×1

Appearance and specifications are subject to change without prior notice or obligations.

SERVICE

The camera is a precision instrument. Handle it carefully and always follow the safety precautions. If the camera requires service, never try to repair it yourself or open the casing.

For servicing, maintenance, or repairs, consult your dealer or an Authorized Sanyo Service Center.

■Dimensions

φ151 (6.0)

	104 (4.2)
φ100 (4.0)	Unit: mm (inch)

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT.

WARNING:

To prevent damage, do not drop the unit or subject it to strong shock or vibration.

■ Do not install this unit close to magnetic fields

INSTALLING BASE PLATE AND CONNECTIONS

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

The magnetic fields may result in unstable operation.

■ Protect from humidity and dust

Open the base plate. Ceiling Installed

Monitor Connection

For the customers in Canada

This Class B digital apparatus complies with Canadian ICES-003.

Pour la clientèle canadienne

Cet appareil numerique de la Classe B est conforme à la norme NMB-003 du Canada.

This installation should be made by a qualified service person and should conform to all local codes.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

To prevent damage, do not install the unit where there is greasy smoke or steam, where the humidity may get too high, or where there is a lot of dust.

■Protect from high temperatures

Do not install close to stoves, or other heat sources, such as spotlights, etc., or where it could be subject to direct sunlight, as this could cause deformation, discoloration or other damages.

Be careful when installing close to the ceiling, in a kitchen or boiler room, as the temperature may rise to high levels.

■Cleaning

• Dirt can be removed from the cabinet by wiping it with a soft cloth.

To remove stains, wipe with a soft cloth moistened with a soft

detergent solution and wrung dry, then dry by wiping with a soft

Push

Point the arrow (↓) in the same direction as the lens orientation.

(A)

•Length: 35 mm/1.4 in. or more

•Diameter: 3.5 to 5.0 mm/0.1 to 0.2 in.

•Height of screw head:

5 mm/0.2 in. or less (washer included)

(A)

(A)

(A)

1

2

(A)

	Cable type	Length
1	RG-59U (3C-2V)	250 m (273 yds) max.
	RG-6U (5C-2V) 500 m (547 yds) max.
	RG-11U (7C-2V)	600 m (656 yds) max.

•When using an RG-59U (3C-2V) cable, do not let it dangle in the air or attach it to piping.

•If you use a cable other than the types above, the image or sync signal will be attenuated and will not be transmitted correctly.

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

–Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by Sanyo may void the user's authority to operate this camera.

cloth.

• Do not use benzine, thinner or other chemical products on the

cabinet, as this may cause deformation and paint peeling. Before

using a chemical cloth, make sure to read all accompanying

instructions. Make sure that no plastic or rubber material comes

into contact with the cabinet for a long period of time, as this may

cause damage or paint peeling.

Make sure to tighten the screws properly.

Using screws of sizes other than specified may cause the unit to fall.

Wall Installed

1

2

Place the base plate so that the arrow points downward.

(A)

(A)

(A)

Power Supply Connection

b With AC 24 V b With DC 12 V

Check that +/- polarity is correct.

	(RED)	~	(RED)	+
2	(BLACK)	~
			(BLACK)	–
	(WHITE)	GND

For the connections, use cables thicker than 18 AWG.

1AC6P1P3265--	SANYO Electric Co., Ltd.
L5CJ2/US (1107KP-HS)	Printed in China

&Reverse side

(A)