English Français Español
INSTRUCTION MANUAL |
|
(Warranty attached) |
|
COLOR CCD Camera |
|
|
Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.
This instruction manual covers the following models. Any difference among the three models is indicated when necessary.
|
| 140.2 (5.5) |
(3.6) | 46.2 (1.8) | 30.0 (1.2) |
91.5 |
|
|
Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer or an Authorized Sanyo Service Center.
INFORMATION TO USER
Safety Guard
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT.
WARNING:TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
For the customers in CanadaThis Class B digital apparatus complies with Canadian
Cet appareil numerique de la Classe B est conforme a la norme
This installation should be made by a qualified service person and should conform to all local codes.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by Sanyo may void the user's authority to operate this camera.
PRECAUTIONS
■In case of a problem
Do not use the unit if smoke or a strange odor comes from the unit, or if it seems not to function correctly. Turn off the power immediately and disconnect the power cord, and then consult your dealer or an Authorized Sanyo Service Center.
■Do not open or modify
Do not open the cabinet, as it may be dangerous and cause damage to the unit. For repairs, consult your dealer or an Authorized Sanyo Service Center.
■Do not put objects inside the unit
Make sure that no metal objects or flammable substance get inside the unit. If used with a foreign object inside, it could cause a fire, a
■Be careful when handling the unit
To prevent damage, do not drop the unit or subject it to strong shock or vibration.
■Do not install this unit close to magnetic fields
The magnetic fields may result in unstable operation.
■Protect from humidity and dust
To prevent damage, do not install the unit where there is greasy smoke or steam, where the humidity may get too high, or where there is a lot of dust.
TROUBLESHOOTING
Before sending the camera out for repair, check the items below. If the problem persists after checking these items, consult your dealer or an Authorized Sanyo Service Center.
■If no image appears
Is the coaxial cable attached securely?
Are the power and voltage normal?
SPECIFICATIONS |
| |||
|
|
|
| |
| ||||
Scanning system | NTSC standard 525 lines, 60 fields/sec. | |||
Image sensor | 1/3" interline transfer method CCD | |||
Number of effective |
| 768 (H) x 494 (V) |
| |
pixels |
|
| ||
|
|
| ||
Horizontal resolution | More than 520 TV lines | More than | ||
480 TV lines | ||||
|
|
| ||
Minimum illumination |
| 0.05 lx |
| |
| (F1.4, B/W mode) |
|
INSTALLATION
| (H) |
(H) | (G) |
| |
| (J) |
| (I) |
82.588.0
(E)
Has the iris of the lens been adjusted correctly (with the level
(approx.) | 1.0 lx (F1.4) | 1.0 lx | 1.0 lx (F1.4) |
|
| ||
|
| (F1.4, color mode) |
|
Video output | 1.0 |
(F)
88.0
volume)?
Is there adequate illumination?
■If the image is unclear
Is the monitor adjusted correctly?
Video S/N ratio | More than 50 dB (AGC off) |
| |
Lens | |||
Pan/Tilt adjustment | Pan: ±180º, Tilt: ±60º (Ceiling Installed) | ||
Backlight compensation | OFF / ON (Center zone metering) |
| – |
Iris setting | AI / EI (Only AI is available for the |
(A)
(B)
46.0
(M)
Is the lens in focus? Is the lens clean?
Dirt or fingerprints on the lens can adversely affect the image. Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid (commercially available).
SERVICE
The camera is a precision instrument. Handle it carefully and always follow the safety precautions. If the camera requires service, never try to repair it yourself or open the casing.
For servicing, maintenance, or repairs, consult your dealer or an Authorized Sanyo Service Center.
White balance | ATW / | ATW / | |||
Gain control |
| ON / OFF |
|
| |
Wide dynamic range | – | – | ON / OFF | ||
Dynamic range | – | – | 54 dB typical | ||
Sync system | DC 12 V user: | Internal sync, AC 24 V user: | |||
Day/Night function | – | Always active |
| – | |
| Temperature: | ||||
Operating environment | (14 - 104°F) | ||||
|
| ||||
| Humidity: less than 90% RH (no | condensation) | |||
Power supply | 24 V AC ±10%, 60 Hz/12 - 15 V DC | ||||
Power consumption | 2.6 W | 2.6 W |
| 4.0 W | |
(approx.) |
| ||||
|
|
|
| ||
Weight (approx.) |
| 850 g (30 oz) |
|
| |
| Hexagonal wrench, Large, Medium and Small | ....... each1 | |||
| Rubber cushion............................................................... |
|
| 1 | |
Accessories | Mounting screw............................................................... |
|
| 4 | |
| Screw hold ...................................................................... |
|
| 4 | |
| Mounting template .......................................................... |
|
| 1 |
The factory setting value is represented in bold.
Appearance and specifications are subject to change without prior notice.
(K)
(D)
(L)
(N)
(C)
Since the conduit hole cover is not
Make sure to perform waterproofing properly to the ceiling or wall where you are installing the unit.
When setting up this camera, make sure that it is installed securely. Check that the installation location is strong enough to bear the camera weight before proceeding. Install on a ceiling or wall that has no surface unevenness. In addition, do not touch the camera unit except when settings and adjustments are necessary.