Section 7

R

A. Charging the Battery

Refer to the battery charger’s manual for specific instructions.

Under normal conditions the engine’s alternator will have no problem keeping a charge on the battery. If the battery has been completely discharged for a long period of time, the alternator may not be able to recharge the battery, and a battery charger will be required.

DO NOT charge a frozen battery. It may explode and cause injury. Let the battery warm before attaching a charger.

Whenever possible, remove the battery from the mower before charging and make sure the electrolyte covers the plates in all cells.

WARNING

BATTERIES PRODUCE EXPLOSIVE GASES. Charge the battery in a well ventilated space so gases produced while charging can dissipate.

Charging rates between 3 and 50 amperes are satisfactory if excessive gassing or spewing of electrolyte does not occur or the battery does not feel excessively hot (over 125°F). If spewing or gassing occurs or the temperature exceeds 125°F, the charging rate must be reduced or temporarily stopped to permit cooling.

B. Jump Starting

1.The booster battery must be a 12 volt type. If a vehicle is used for jump starting, it must have a negative ground system.

2.When connecting the jumper cables, connect the positive cable to the positive battery post, then connect the negative cable to the negative battery post.

7.8 Drive Belts

All drive belts are spring-loaded and self-tensioning, however after the first 2, 4, 8 and 10 hours of operation, the belts should be checked for proper alignment and wear. Thereafter, check the belts after every 40 hours of operation or weekly, whichever occurs first.

- NOTE -

If you experience frequent belt wear or breakage, see your authorized Scag service center for belt adjustment.

7.9 Cutter Blades

A. Blade Inspection

1.Remove the ignition key before servicing the blades.

2.Raise the mower deck to the highest position. Place the lanyard pin in the highest cutting height position to prevent the cutter deck from falling.

WARNING

Always wear proper hand and eye protection when working with cutter blades.

3.Check the cutter blades for straightness. If the cutter blades appear bent, they will need to be replaced.

WARNING

Do not attempt to straighten a bent blade, and never weld a broken or cracked blade. Always replace it with a new blade to assure safety.

4.If a blade cutting edge is dull or nicked, it should be sharpened. Remove the blades for sharpening. See "Blade Replacement."

- NOTE -

Keep the blades sharp. Cutting with dull blades not only yields a poor mowing job, but slows the cutting speed of the mower and causes extra wear on the engine and the blade drive by pulling hard.

B. Blade Sharpening

- NOTE -

If possible, use a file to sharpen the blade. Using a wheel grinder may burn the blade.

37

Page 40 Page 42
Page 41
Image 41
Scag Power Equipment STT61V-29KB-DF manual Drive Belts, Cutter Blades
Page 40 Page 42

STT61V-29KB-DF specifications

The Scag Power Equipment STT61V-29KB-DF is a robust and powerful zero-turn mower designed for professional landscapers and homeowners seeking superior performance and efficiency. With a 61-inch cut width and a powerful 29 HP Kawasaki engine, this mower offers exceptional cutting capabilities, enabling users to tackle large lawns and challenging terrain with ease.

One of the standout features of the STT61V-29KB-DF is its patented Velocity Plus cutting deck. This innovative design enhances grass flow, resulting in a clean and precise cut. The deck's airflow is optimized to lift the grass for an even cut, ensuring a professional-quality finish every time. The mower's cutting height can be easily adjusted to suit different types of grass and seasonal conditions, providing versatility for various mowing tasks.

In addition to its performance features, the STT61V-29KB-DF is built with durability in mind. The heavy-duty steel frame and reinforced cutting deck provide lasting durability, allowing it to withstand the demands of frequent use in tough environments. The mower also boasts a high-quality paint finish that protects against rust and corrosion, ensuring the machine remains in great condition even after years of use.

The ergonomic design of the STT61V-29KB-DF enhances operator comfort and control. The cushioned seat provides support for long mowing sessions, while the easy-to-use joystick controls allow for smooth maneuverability and precise handling. This design reduces operator fatigue and increases productivity, making it a favorite among landscape professionals.

Another notable technology in the STT61V-29KB-DF is its hydrostatic transmission, which provides seamless speed and direction changes without the need for gear shifting. This feature allows for superior control and responsiveness, especially when navigating around obstacles or tight spaces.

Safety features are also prioritized in the design of this mower. It includes an automatic safety shut-off system that stops the blades when the operator leaves the seat, while the robust structure provides stability on slopes and uneven terrain.

Overall, the Scag Power Equipment STT61V-29KB-DF is a top-tier zero-turn mower that combines power, performance, and user-friendly features, making it an ideal choice for anyone looking to achieve a flawless cut while ensuring maximum operator comfort and safety. With its blend of advanced technologies and durability, this model stands out in the competitive market of landscaping equipment.
Top Page Image Contents