CHARGING
NOTE: Will also charge your iPod until transmitter charge is full.
Before using this for the first time, charge the headphones and transmitter for a full 2.5 hours. A cable is provided in the kit for charging.
1.Plug the Mini cable end of the charger cord into the charging jack as shown in Illustration 2.
2.Connect USB Cable to an available PC/Laptop USB port or 110v AC USB wall adapter/ power supply. (AC adapter not included).
3.Charge Battery for 2.5 hours (LED will illuminate RED when charging).
4.The RED LED will turn off when charging is complete. Unplug each device and enjoy up to 5 hours of use.
5.Purchase wall and car adapters to charge at home and/or on the road. (IPPWR / IP2IN1 - Sold Separately)
ILLUSTRATION 2 | OPTIONAL |
| |
CHARGING CONNECTIONS | WALL OUTLET | ||
WALL ADAPTER | |||
| (NOT INCLUDED) |
| |
SCOSCHE UBHP |
|
| |
HEADPHONES |
|
| |
| USB |
| |
| CABLE |
| |
NOT TO SCALE | IPBTT Transmitter |
| |
| PAIRING |
|
GENERAL PAIRING NOTES:
1.Keep the Bluetooth® products within a distance of 3 ft. ( 1 meter) when pairing.
2.These products are designed for
3.As a general rule, power the receiving device FIRST before the transmitting device. (Headphone is the receiver)
4.Compatible devices must be Bluetooth® v1.2 supporting A2DP profile.
5.Turn off any other nearby Bluetooth® devices, such as a cell phone or headset as this may hinder pairing process between your devices.
6.Pairing can take up to 1 minute, sometimes more. Once initial pairing is complete between your headphones, transmitter and Bluetooth® phone, reconnecting during normal use occurs in a fraction of the time.
PAIRING UBHP HEADPHONES TO THE IPBTT TRANSMITTER:
1.Press the Power Button on the UBHP headphones for 3 seconds. Blue LED will flash indicating pairing mode.
2.Press the power Button on the IPBTT transmitter for 3 seconds. Blue LED will flash quickly indicating pairing mode.
3.Pairing should occur within 1 minute but can take up to 5 minutes. Blue LED will stop flashing on the headphones and flash slowly on the transmitter.
4.Plug the transmitter into your iPod bottom dock. You should hear the audio through your Bluetooth® Headphones.
5.If you are successful pairing the devices, repeat steps
2
PAIRING CONTINUED
PAIRING UBHP HEADPHONES TO A BLUETOOTH® CELL PHONE:
1.Place headphones and Bluetooth cell phone with in 3 ft. (1m) of each other.
2.Ensure headphone power is off.
3.Press the power button on the right earpiece for 3 seconds. The Blue LED will flash indicating pairing mode.
4.While the headphone LED is flashing Blue, follow the instructions for your cell phone to seek (or discover) any Bluetooth® devices. You will be pairing the Scosche Bluetooth® headphones to your phone just like you would pair any Bluetooth® handset or
5.Your cell phone should display a list of local Bluetooth® devices. The Scosche headphones should be displayed as a device named "SCOSCHE" Headphones.
6.Select this device and your cell phone should connect to this device automatically. If your phone happens to ask for a password (or passcode) then enter "0000".
7.Bluetooth® pairing should now be complete. (Blue LED on solid) If your phone fails to locate the Scosche headphones, then check to make sure your phone is seeking Bluetooth® devices. Check to make sure the Scosche headphone power is switched ON and the LED light is flashing Blue indicating "pairing" mode.
Repeat steps
8.Place the headphones over your ears and make a test call from your cell phone. Your cell phone audio should be heard through the headphones.
HEADPHONE & TRANSMITTER OPERATION
POWER ON/OFF NOTE:
Under normal use, we suggest powering on the headphones (receiver) first, then power on your Bluetooth® transmitter. This method will produce the shortest connection time between the devices. if using a Bluetooth® cell phone, then connect to the headphone AFTER the transmitter is connected as the third device in your group. If you have previously paired with your Bluetooth® cell phone, then select the Scosche headphones from the Bluetooth® device list and choose to connect.
POWER ON OFF: Press the Power Button for 3 seconds to turn the transmitter ON or OFF
CONNECTION
Connect IPBTT to the bottom dock of your iPod. Turn the IPBTT on, then turn on your Bluetooth® headphones or receiving device. Once the two devices are paired, enjoy the audio.
REMOTE CONTROL SOURCE FUNCTIONS
ONLY when used with device that support the AVCRP profile for remote control functions. ( Scosche Bluetooth® headphones - UBHP)
- PLAY/PAUSE
Press the power button on your Bluetooth® headphones (or other receiving devices) to PLAY or PAUSE the current track. Do not hold down the power button for
for more than 1 second or it may turn off the power.
(NOTE: Volume control will no longer be controlled through iPod wheel, only through Bluetooth® device controls).
- TRACK UP/DOWN
1.Press and hold the volume up button to skip forward to the next track.
2.Press and hold the volume down button to skip back to the beginning of the song.
3.To track to previous song press and hold immediately after step (2).
CELLULAR OPERATION
INCOMING CALL ANSWER:
With your UBHP headphones powered and a Bluetooth® wireless link established, a ring tone will be heard inside the headphones when you receive an incoming phone call. Simply press and release the Power Button to ANSWER an incoming call. If you were listening to music at the time, it will be interrupted during your call. You will hear the other party through the left headphone speaker and they will hear you through the
ENDING A CALL:
When you are finished with the call, simply press and release the Power Button to END the call.
CELLULAR RE-CONNECTING:
Once you have initially paired your cell phone with the UBHP Bluetooth® headphones, operating steps may vary when needing to
3
