Seagate 2531, 3240 - page 19

any drive activity is re quired, the drive makes a t ransition to Idle mode.

If the host has set the s tandby ti mer, the st andby count down continues .

If the host has not set the stand by timer, the drive r emains in Idle mode.

If the standby timer reaches zero before any dri ve act ivi ty is requi red, the

drive makes a transition to Standby mode. In both I dle and Standby

mode, the drive accepts al l comm ands and r eturn s t o Acti ve mod e wh en

disc access is necessary.

1.8 Environmental tolerances

1.8.1 Ambient temperature

Operating 5° to 55°C (41° to 131°F)

Nonoperating –40° t o 60°C (–40° to 140°F)

Note. Above 1, 00 0 feet (305 met ers) , the maxim um temp erat ure is der-

ated linearly to 112 °F (44°C) at 10,000 feet (3,048 meters). Oper-

ating ambient temperature is defined as the temperature of t he

environment immediately surro unding the drive.

1.8.2 Temperature gradient

Operating 20°C / hr (68°F / hr) max, without condensation

Nonoperating 20°C / hr (68°F / hr) max, without condensation

1.8.3 Humidity

1.8.3.1 Relative humidity

Operating 8% to 80% noncondensing (10% per hour max)

Nonoperating 8% to 80% noncondensing (10% per hour max)

1.8.3.2 Wet bulb temperature

Operating 28.9°C (84°F) max

Nonoperating 28. 9°C (84°F) max

1.8.4 Altitude

Operating –61 m to 3,048 m (–200 ft to +10,000 ft)

Nonoperating –61 m to 12,192 m (–200 ft to +40,000 ft)

Medalist 3240 and Medalist 2531 Product Manual, Rev. A 11

Contents

Main Page Page Page Contents Page Page Page Introduction Specification summary table 2 Medalist 3240 and Medalist 2531 Product Manual, Rev. A Drive Spe cificati on ST33240A ST32531A Medalist 3240 and Medalist 2531 Product Manual, Rev. A 3 Page 1.0 Drive specifications this drive all n the drive 1.2 Physical organization 1.3 Recording and interface tec hn ology 1.4 Physical characteristics 1.5 Seek time 1.6 Start/stop times 1.7 Power specifications 1.7.1 Power consumption 1.7.1.1 Typical current profile 1.7.2 Conduct ed noise 1.7.3 Voltage tolerance 1.7.4 Power-management modes Page 1.8.5 Shock 1.8.5.1 Operating shock 1.8.5.2 Nonoperating shock 1.8.6 Vibration 1.8.6.1 Operating vibration 1.8.6.2 Nonoperating vibration 1.9 Drive acoustics 1.10 Electromagnetic susceptibility 1.11 Reliability 1.12 Agency certification 1.12.1 Safety certification 1.12.2 Electromagnetic Compatibility 1.12.3 FCC verification How to Identify and Resolve Radio-Television Interference Problems Page 2.0 Drive mounting and configuration 2.1 Handling and static-d isch ar ge pr ecau ti on s 2.2 Jumper settings 2.2.1 Master/slave configuration 2.2.2 Alternate capacity jumper 2.3 Drive mounting Medalist 3240 and Medalist 2531 Product Manual, Rev. A 19 xx xxx Figure 3. Mounting dimensions for the ST33240A and ST32531Atop, side and end view Page 3.0 ATA interface Draft ATA-3 document X3T10 2008, Revision 6, Draft Proposed ATA-3 Standard 3.1 ATA interface signals and connector pins Draft Proposed ATA-3 Standard. 22 Medalist 3240 and Medalist 2531 Product Manual, Rev. A Figure 4. I/O pins and supported ATA signals 3.2 ATA Interface commands 3.2.1 Supported ATA commands Draft Proposed ATA-3 Standard. Page Draft Proposed ATA-3 Standard 3.2.2 Identify Drive command xx Page 3.2.3 Set Features command 3.2.4 S.M.A.R.T. commands Draft Proposed ATA-3 Standard.