Set Features command, 0CH | Seagate Medalist 17242 specs

30	Medalist 17242, 13032, 10232, 8422 and 4312, Rev. A

8Ultra DMA mode 0 is currently active.

9Ultra DMA mode 1 is currently active.

10Ultra DMA mode 2 is currently active.

11Ultra DMA mode 3 is currently active.

12Ultra DMA mode 4 is currently active.

Bit Word 93

131=80-conductor cable detected, CBLID above VIH 0=40-conductor cable detected, CBLID below VIL

3.2.3Set Features command

This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the Features register are defined as follows:

02H	Enable write cache (default).
03H	Set transfer mode (based on value in Sector Count register).
	Sector Count register values:
	00H	Set PIO mode to default (PIO mode 2).
	01H	Set PIO mode to default and disable IORDY
		(PIO mode 2).
	08H	PIO mode 0
	09H	PIO mode 1
	0AH	PIO mode 2 (default)
	0BH	PIO mode 3
	0CH	PIO mode 4
	20H	Multiword DMA mode 0
	21H	Multiword DMA mode 1
	22H	Multiword DMA mode 2

Image 38

Seagate Medalist 17242 manual Set Features command, 0CH

Contents

Product Manual Page Product Manual Page Contents ATA interface Figures Viii Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a Introduction Specification summary table ST317242A ST313032A Relative humidity Gradient LBA Mode Default logical geometryDrive Guaranteed Mbytes Bytes per Model Formatted capacity Recording and interface technology Supported CHS translation geometriesPhysical organization Drive Model Read/Write heads MR Number of discs Seek time Physical characteristicsDrive Specification ST310232A, ST38422A ST34312A ST317242A, ST313032A Start/stop times Power specificationsPower consumption Read Write Seek type Msec, typ Mode Typical Watts RMS Typical Amps RMS 12V Typical current profile Conducted noise Power-management modesMode Heads Spindle Buffer Voltage tolerance 3.2 Wet bulb temperature Environmental tolerances Ambient temperatureTemperature gradient Humidity 3.1 Relative Humidity Operating shock AltitudeShock Nonoperating shock Drive acoustics Typical sound Maximum sound Mode Power belsNonoperating vibration Electromagnetic susceptibility Electromagnetic Compatibility Agency certification Safety certificationReliability Australian C-Tick FCC verification Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a Handling and static-discharge precautions Jumper settings Master/slave configuration Alternate capacity jumper Ultra ATA/66 cable Alternate capacity and master/slave jumper settings Drive mounting Mounting dimensions-top, side and end view Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a ATA interface signals and connector pins ATA interface O pins and supported ATA signals ATA-standard commands ATA Interface commands Supported ATA commandsCommand name Supported by Code ATA-standard power-management commands Identify Drive command Word Description Value Word Description 60-61 Total number of user-addressable Description if bit is set to Bit Word Set Features command 0CH A.R.T. Read Data Yes 4 S.M.A.R.T. commandsA.R.T. Enable/Disable Attribute Yes Autosave Vendor-specific Yes D3H Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a