Manuals / Seagate / Computer Equipment / Computer Drive

Seagate ST3320820AS Configuring and mounting the drive, Handling and static-discharge precautions

Models: ST3200820AS ST3300820AS ST3300620AS ST3500641ASRK ST3400820AS ST3250820AS ST380215AS ST3320620AS ST3160215AS ST340215AS ST340815AS ST3120815AS ST380815AS ST3250620AS ST3250310AS ST3160815AS ST3320820AS ST3250410AS ST3120215AS

1 68

Download 68 pages 14.65 Kb

Page 47

3.0Configuring and mounting the drive

3.0Configuring and mounting the drive

This section contains the specifications and instructions for configuring and mounting the drive.

3.1Handling and static-discharge precautions

After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis- charge (ESD) hazards. Observe the following standard handling and static-discharge precautions:

Caution:

•Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure.

•Handle the drive by its edges or frame only.

•The drive is extremely fragile—handle it with care. Do not press down on the drive top cover.

•Always rest the drive on a padded, antistatic surface until you mount it in the computer.

•Do not touch the connector pins or the printed circuit board.

•Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination.

Barracuda 7200.10 Serial ATA Product Manual, Rev. K

41

Image 47

Seagate ST3320820AS, ST3120215AS, ST3120815AS Configuring and mounting the drive, Handling and static-discharge precautions

Contents

Barracuda 7200.10 Serial ATA evision history 5.0 Seagate Technology support services Contents2.0 Drive specifications 3.0 Configuring and mounting the driveBarracuda 7200.10 Serial ATA Product Manual, Rev. K Typical 12V startup and operation current profile List of FiguresSerial ATA connectors Typical 5V startup and operation current profilePage 1.0 Introduction 1.1 About the Serial ATA interface 2.1 Specification summary tables 2.0 Drive specificationsBarracuda 7200.10 Serial ATA Product Manual, Rev. K Drive specifications summary for 750 Gbyte modelsFrom this page, click on the “Verify Your Warranty” link. You will be asked Barracuda 7200.10 Serial ATA Product Manual, Rev. K Drive specifications summary for 500 Gbyte modelsTo determine the warranty for a specific drive, use a web browser to access Barracuda 7200.10 Serial ATA Product Manual, Rev. K Drive specifications summary for 400 Gbyte modelsBarracuda 7200.10 Serial ATA Product Manual, Rev. K Barracuda 7200.10 Serial ATA Product Manual, Rev. K Drive specifications summary for 320 Gbyte modelsBarracuda 7200.10 Serial ATA Product Manual, Rev. K To determine the warranty for a specific drive, use a web browser toBarracuda 7200.10 Serial ATA Product Manual, Rev. K Drive specifications summary for 300 Gbyte modelsBarracuda 7200.10 Serial ATA Product Manual, Rev. K ST3250410AS Drive specificationST3250620AS ST3250820ASST3250410AS Drive specificationST3250620AS ST3250820ASBarracuda 7200.10 Serial ATA Product Manual, Rev. K Drive specifications summary for the 200 Gbyte modeSupports Hotplug operation per the Serial ATA Revision 2.5 spec To determine the warranty for a specific drive, use a web browserBarracuda 7200.10 Serial ATA Product Manual, Rev. K Barracuda 7200.10 Serial ATA Product Manual, Rev. K Drive specifications summary for the 160 Gbyte modelsBarracuda 7200.10 Serial ATA Product Manual, Rev. K Barracuda 7200.10 Serial ATA Product Manual, Rev. K Drive specifications summary for the 120 Gbyte modelsBarracuda 7200.10 Serial ATA Product Manual, Rev. K 40C max nonoperating Drive specifications summary for the 80 Gbyte modelsBarracuda 7200.10 Serial ATA Product Manual, Rev. K Barracuda 7200.10 Serial ATA Product Manual, Rev. K Drive specifications summary for the 40 Gbyte modelsBarracuda 7200.10 Serial ATA Product Manual, Rev. K LBA mode 2.3 Default logical geometry2.2 Formatted capacity 2.2.1 LBA modeBarracuda 7200.10 Serial ATA Product Manual, Rev. K 2.4 Recording and interface technologyMaximum height 1 disc models Physical characteristicsTypical weight Maximum height 4, 3 and 2 disc modelsMeasured in performance mode. **Measured in quiet mode 2.6 Seek time2.7 Start/stop times Operating power and current 2.8.1 Power consumptionSpinup power Read/write power and currentFigure 1. Typical 5V startup and operation current profile 2.8.1.1 Typical current profiles2.8.2 Conducted noise 2.8.3 Voltage toleranceIdle mode 2.8.4 Power-management modesIdle and Standby timers Active mode2.9.3 Humidity 2.9.3.1 Relative humidity 2.9.1 Ambient temperature2.9.2 Temperature gradient 2.9.3.2 Wet bulb temperature2.9.6.1 Operating vibration 2.9.5.2 Nonoperating shock 1 and 2 Disc models3 and 4 Disc models 2.9.6 Vibration2.10.1 Test for Prominent Discrete Tones PDTs 2.10 AcousticsTable 13 Fluid Dynamic Bearing FDB motor acoustics Table 14 Radio frequency environments 2.11 Electromagnetic immunity2.13.2 Electromagnetic compatibility 2.13.1 Safety certification2.12 Reliability 2.13 Agency certification2.13.3 FCC verification Korean RRLAustralian C-Tick N176 2.14.2 中国限制危险物品的指令 2.14 Environmental protection2.15 Corrosive environment 2.14.2 China Restriction of Hazardous Substances RoHS DirectiveBarracuda 7200.10 Serial ATA Product Manual, Rev. K 3.1 Handling and static-discharge precautions 3.0 Configuring and mounting the driveFigure 4. Attaching SATA cabling 3.2 Configuring the drive3.3 Serial ATA cables and connectors Figure 3. Serial ATA connectors28.499 Recommended case temperature measurement location1 Recommended case temperature measurement location 3.4 Drive mountingBarracuda 7200.10 Serial ATA Product Manual, Rev. K 4.1 Hot-Plug compatibility 4.0 Serial ATA SATA interfaceSerial ATA connector pin definitions 4.2 Serial ATA device plug connector pin definitionsTable 16 Supported ATA commands 4.3 Supported ATA commandsBarracuda 7200.10 Serial ATA Product Manual, Rev. K Command nameCommand code in hex Firmware revision 8 ASCII character string, padded with blanks to end 4.3.1 Identify Device commandValue Barracuda 7200.10 Serial ATA Product Manual, Rev. KWord DescriptionTotal number of user-addressable LBA sectors available see Section Barracuda 7200.10 Serial ATA Product Manual, Rev. KxxxxH Multiword DMA mode 0 is supported Set PIO mode to default and disable IORDY PIO mode 4.3.2 Set Features commandTable 17 Set Features command values S.M.A.R.T. command 4.3.3 S.M.A.R.T. commandsTable 18 S.M.A.R.T. commands Code in features registerWarranty Support 5.0 Seagate Technology support servicesOnline services Seagate Service CentersAsia/Pacific Support Services Customer Service OperationsUSA/Canada/Latin America support services Europe, the Middle East and Africa Support ServicesIndex Page Page Barracuda 7200.10 Serial ATA Product Manual, Rev. K Page Publication Number 100402371, Rev. K, Printed in U.S.A Seagate Technology LLC920 Disc Drive, Scotts Valley, California 95066-4544, USA