Manuals / Seagate / Computer Equipment / Computer Drive

Seagate ST446452W manual Initial setup information, Drive termination Terminator power

Models: ST446452W

1 46

Download 46 pages 22.06 Kb

Page 20

18	Elite 47 Installation Guide, Rev. B

Initial setup information

The following topics are discussed in this section:

•SCSI ID jumpers

•Drive termination

•Terminator power

•Interface drivers and data path width notes

•Other applicable jumper options

•Providing adequate cooling

•Mounting the drive and connecting cables

•Formatting the drive

Image 20

Seagate ST446452W manual Initial setup information, The following topics are discussed in this section SCSI ID jumpers

Contents

Installation Guide EliteDisc Drive ST446452WContents Preface Electrostatic discharge protectionImportant safety information and precautions Seagate takes all reasonable steps to ensure that its products are certifiable to currently accepted standards. Typical applica- tions of these disc drives include customer packaging and sub- system design. Safety agencies conditionally certify component assemblies, such as the Elite disc drive, based on their final acceptability in the end-use product. The subsystem designers are responsible for meeting these conditions of acceptability in obtaining safety-regulatory agency compliance in their end-use products and for certifying where required by law. A necessary part of meeting safety requirements is the provision for overcur- rent protection on drive SELV supply voltages Wichtige Sicherheitshinweise Elite 47 Installation Guide, Rev. B Page Electromagnetic compliance Regulatory agency complianceElectromagnetic susceptibility Electromagnetic compliance for the European Union Australian C-TickTechnical support services Online servicesSeaFONE 1-800-SEAGATE SeaNETSeagate CompuServe forum SeaBOARDSeagate technical support FAX FAX servicesSeaFAX SeaTDD Direct-support servicesSeagate technical support Customer service centers Manufacturer’s representativesGeneral description Figure 1. Elite 47 disc driveTable 1 Drive characteristics Table 2 DC power requirements Single-ended+5V8,10 +12V8 Voltage regulation5Dimensions of the drive Initial setup information Drive termination Terminator powerMounting the drive and connecting cables Formatting the drive The following topics are discussed in this section SCSI ID jumpersSCSI ID jumpers Figure 2. Setting the SCSI ID Drive termination Terminating the drive Figure 3. SCSI bus terminationTerminator power Figure 4. Terminating the driveFigure 5. Setting terminator power jumpers I/O circuits and data path widthsTable 4 Cable characteristics for single-ended circuits 5 Mbytes/s6 meters 19.7 ft 3 meters 9.8 ftFigure 6. 68-pin wide connection to drive Elite 47 Installation Guide, Rev. BFigure 7. Multiple-drive connection to host adapter SCSI ID X or last drive SCSI ID SCSI IDAdditional SCSI devices Pin check your adapter for Pin 1 location SCSI ID Host Adapter PCBOther applicable jumper options Figure 8. Additional jumper optionsActive, Ready, and Fault indicators Figure 9. LED indicator connectionsProviding adequate cooling Kühlung des Systems Elite 47 Installation Guide, Rev. B Figure 10. Suggested air flowAbbildung 10.Empfohlener Luftstromverlauf Mounting the drive and connecting cables Installation des Laufwerkes und Anschluß der Kabel3. Verify that you have correctly installed jumpers Pin Gleichstrom Figure 11. DC power connector Abbildung 11.GleichstromanschlußPin Power Hinweis 5. Setzen Sie das Gehäuseoberteil des Host-Systems wieder auf Elite 47 Installation Guide, Rev. B5. Replace the host system’s cover Figure 12. Mounting configuration dimensions K HG D A EFormatting the drive Quick reference desktop system notesPage Page Seagate Technology, Inc 920 Disc Drive, Scotts Valley, CA 95066-4544, USAPublication Number 83329290, Rev. B, Printed in USA Elite 47 Installation Guide, Rev. BElite 47 Installation Guide, Rev. B