Manuals / Seagate / Computer Equipment / Computer Drive

Seagate ST930813AM Configuring and mounting the drive, Handling and static discharge precautions

Models: ST940813AM ST920814AM ST920813AM ST940814AM ST930813AM ST930814AM

1 44

Download 44 pages 23.25 Kb

Page 27

3.0Configuring and mounting the drive

3.0Configuring and mounting the drive

This section contains the specifications and instructions for configuring and mounting the drive.

3.1Handling and static discharge precautions

After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis- charge (ESD) hazards. Observe the following standard handling and static-discharge precautions:

Caution:

•Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation to limit the drive’s exposure to ESD.

•Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure.

•Handle the drive only by its edges or frame.

•The drive is fragile—handle it with care. Do not press down on the drive top cover.

•Always rest the drive on a padded, antistatic surface until you mount it in the computer.

•Do not touch the connector pins or the printed circuit board.

•Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination.

3.2Jumper settings

3.2.1Master/slave configuration

Use the options jumper block shown in Figure 3 to configure the drive for operation. This jumper block is the 4-pin header adjacent to pins 1 and 2 of the I/O signal pins. For additional information about using the Cable select option, see Section 3.2.2.

The “Drive is master (or single drive)” option is the default setting.

Drive is master (or single drive)

Drive is slave

Cable select

Figure 3. Jumper settings

EE25 Series Product Manual, Rev. E

21

Image 27

Seagate ST930813AM manual Configuring and mounting the drive, Handling and static discharge precautions, Jumper settings

Contents

ST940813AM ST940814AM ST930813AM ST930814AM ST920813AM ST920814AM EE25 SeriesProduct Manual August 5.0 Seagate Technology support services Contents1.0 Introduction 2.0 Drive specifications 3.0 Configuring and mounting the driveEE25 Series Product Manual, Rev. E List of Figures EE25 Series Product Manual, Rev. E 1.0 Introduction EE25 Series Product Manual, Rev. E 2.1 Specification summary 2.0 Drive specificationsEE25 Series Product Manual, Rev. E Specifications for 40 and 30 Gbyte modelsfollowing web page EE25 Series Product Manual, Rev. E1.0 G 200 - 500 Hz 5.0 Gs 0 to peak, 5-500 Hz X, Y, Z axis 0, 22, 45 angles5% to 90% operating Specifications for 20 Gbyte modelsST920814AM Drive specificationEE25 Series Product Manual, Rev. E ST920813AMLBA mode 2.3 Default logical geometry2.2 Formatted capacity 2.4 Physical organizationSpecification 2.6 Physical characteristics2.5 Recording and interface technology 2.7 Seek timeEE25 Series Product Manual, Rev. E Start/stop timesRead/write power and current 2.9 Power specifications2.9.1 Power consumption Spinup powerFigure 1. Typical 5V startup and operation current profile 2.9.1.1 Typical current profile2.9.2 Conducted noise 2.9.3 Voltage toleranceIdle mode 2.9.4 Power-management modesIdle and Standby timers Active mode2.10.3.2 Wet bulb temperature 2.10 Environmental specifications2.10.1 Ambient temperature 2.10.2 Temperature gradientFigure 2. Temperature vs. altitude capability 2.11.1 Shock2.11.1.1 Operating shock 2.11.1.2 Nonoperating shock2.11.2.2 Nonoperating vibration 2.12 Acoustics2.11.2 Vibration 2.11.2.1 Operating vibration2.13 Electromagnetic immunity 2.14Reliability Korean RRL 2.15.1 Safety certification2.15 Agency certification 2.15.2 Electromagnetic compatibility2.16 Environmental protection 2.17 Corrosive environment2.16.1 European Union Restriction of Hazardous Substances RoHS EE25 Series Product Manual, Rev. E 3.2.1 Master/slave configuration 3.0 Configuring and mounting the drive3.1 Handling and static discharge precautions 3.2 Jumper settings3.2.2 Cable-select option 3.3 Drive mounting4.0 ATA interface 4.1 ATA interface signals and connector pinsATA-standard commands 4.1.1 Supported ATA commandsCommand name Command code in hex9AH, FAH, FBH EE25 Series Product Manual, Rev. E4.1.2 Identify Device command xx3FH xxxxHxxxxH xx07HxxxxH EE25 Series Product Manual, Rev. EDisable write cache 4.1.3 Set Features commandEE25 Series Product Manual, Rev. E Internet 5.0 Seagate Technology support servicesSeagate Service Centers Warranty SupportAsia/Pacific Support Services Customer Service OperationsUSA/Canada/Latin America support services Europe, the Middle East and Africa Support ServicesIndex NumericsPage Page EE25 Series Product Manual, Rev. E Page 920 Disc Drive, Scotts Valley, California 95066-4544, USA Seagate Technology LLC