Manuals / Seagate / Computer Equipment / Computer Drive

Seagate ST980313ASG, ST9500325ASG manual Drive mounting, Top cover stiffness/deflection

Models: ST9120315AS ST9500325AS ST9160314ASG ST9320325ASG ST9120315ASG ST9250315AS ST9320325AS ST980313AS ST9160314AS ST9250315ASG ST9400326AS ST9160301AS ST9500325ASG ST980313ASG

1 48

Download 48 pages 33.8 Kb

Page 29

3.4Drive mounting

You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 4 for drive mounting dimensions. Follow these important mounting precautions when mount- ing the drive:

•Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.

•Use only M3 UNC mounting screws.

•Do not overtighten the mounting screws. Maximum torque: 4.0 inch-lb (0.4519 N-m).

•Four (4) threads (0.080 inches, 2.032 mm) minimum screw engagement recommended.

•Avoid excessive drive distortion when mounting. Refer to the following specifications for stiffness/deflection information:

Top cover stiffness/deflection

Operating with no performance degradation, emitted noise,	10 mm probe: 2.0kgf OR
mechanical damage, or hard errors	5 mm probe: 0.92kgf

Non-operating with no hard errors	20 mm probe: 2kgf at any point of top cover
	20 mm probe: 15kgf at top cover edges only

Momentus 5400.6 SATA Product Manual, Rev. E

23

Image 29

Seagate ST980313ASG, ST9500325ASG, ST9400326AS, ST9320325ASG manual Drive mounting, Top cover stiffness/deflection

Contents

Momentus 5400.6 Sata Page Contents Momentus 5400.6 Sata Product Manual, Rev. E List of Figures Page Introduction About the Serial ATA interface Drive specifications for 500, 400 and 320 GB models Drive specificationsSpecification summary table Revision 2.6 specification See notes after Table Drive specifications for 250 and 160 GB models Drive specifications for 250 and 160 GB models Drive specifications for 120 and 80 GB models Formatted capacity Formatted Guaranteed Bytes per Model Capacity Sectors LBA mode Default logical geometryPhysical organization Recording and interface technology Seek time Physical characteristicsStart/stop times Typical seek times Power specifications Deferred spinup Typical current profileConducted noise Voltage tolerance Power management modes Power-management modesActive mode Idle mode Environmental specifications Operating shock ShockNonoperating shock Vibration Acoustics Drive A-weighted Sound Power Levels SWL, BAElectromagnetic immunity Test for Prominent Discrete Tones PDTs Reliability Free Fall Protection featureMeasurement type Specification Agency certification Safety certificationElectromagnetic compatibility Korean RRL FCC verification Corrosive environment Environmental protectionEuropean Union Restriction of Hazardous Substances RoHS China Restriction of Hazardous Substances RoHS Directive Handling and static-discharge precautions Configuring and mounting the drive Serial ATA cables and connectors Configuring the drive Top cover stiffness/deflection Drive mounting Measurements shown in are in inches Signal Serial ATA connector pin definitionsSerial ATA Sata interface Segment Pin Function Definition P10 Ground 2nd mate P11 Reserved Pin Function Definition Command name Command code in hex ATA-standard commands Supported ATA commands ATA-standard security commands Command name Command code in hex Word Description Value Identify Device command XxxxH Description if bit is set to Bit Momentus 5400.6 Sata Product Manual, Rev. E Set Features command values Set Features command Code in features register A.R.T. command 3 S.M.A.R.T. commandsM.A.R.T. commands Technical Support Seagate Technology support servicesPresales Support Data Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Index Page Page Momentus 5400.6 Sata Product Manual, Rev. E Page Seagate Technology LLC