![TYPICAL UNDERSINK iNSTALLATiONS / TOOLS AND](/images/new-backgrounds/65857/658579x1.webp)
TYPICAL UNDERSINK iNSTALLATiONS / TOOLS AND
|
| SOLDERED | COPPER | INSTALLATION | |
TO SINK | L] | (OBSERVE | FIG. 1 NOTES) | / | 318"copper |
|
|
| pipe, as req'd. | ||
FAUCET | I,_ |
|
| ,# | _ 90_elbow (4) |
................I | o.or, | ||
NPT x sweat | |||
| i | I (apply | several wraps of |
II Teflon tape to threads)
/- MATERIALS AND TOOLS NEEDED -
shutoff valve | (see page 6) |
MATERIALS NEEDED
INSTALLATION, WITH
FAUCET KIT, Sears Stock
No,
FAUCET
(fiftered water)
adaptor | Mounting Bracket - includes |
| screws, Sears Stock |
saddM valve | No |
| with Deluxe model) |
| , | THREADED | INSTALLATION |
|
|
| ||||
| I I | (OBSERVE | FIG_ 1 NOTES) |
|
|
|
|
| ||
TO SINK | I:::d |
|
|
|
|
|
|
|
|
|
FAUCET | 1_ |
| ..../ | union fitting |
|
|
|
|
| |
,,A,, | F:_ |
| .dElft |
| __ | 3/8" | etbow (3) |
|
|
|
,U,_ |
| tt_- | ore' _ / |
| 3/8" street |
|
|
| ||
,a_ | \ | ,_at- | _ | 'I | elbow |
|
|
| ||
|
|
| ! ' |
|
|
|
|
|
| |
| i_" | 1_ | ! | I |
| apply several |
|
|
| |
| [] | 3/8" nipple | (5)1 | I |
| wraps of Teflon |
|
|
| |
|
|
| J |
| tape to all | Note; Be sure | to allow a |
| ||
|
|
| I | I |
|
| threads | minimum space ol |
| |
|
|
|
|
| under the filterior | removing the | 4, | |||
|
| - MATERIALS AND TOOLS NEEDED - | ||||||||
|
| sump, to change | the cartridge | 4- | ||||||
shutoff valve |
| (see page 7) |
|
|
| |||||
|
|
|
|
|
|
| ||||
|
|
|
| INSTALLATION | STEPS |
|
|
A. USING COMPRESSION FITTINGS, FIG. 1
Note: If plumbing with flexible tubing, hang or sup- port the filter' housing in some manner: Using the mounting bracket (included with Deluxe model) as shown in FIG 1 and 4 is suggested.
1.Apply several wraps of' Teflon tape to the threads of both compression adaptor's
2.CAREFULIX, turn the compression adaptors into the water filter head inlet and outlet, and tighten, Do
not
3.CAUTION: Turn offthe water supply to the sink cold pipe. Open the sink cold faucet to relieve pres- sure in the pipe,
Note: If the sink faucet is a single lever, mixing type,
also close the shutoff valve on the hot water side.
4.Use a tubing cutter to remove a section of the cold water' pipe (catch trapped water with a rag or tow- el) Remove al! bur,s and rough edges with the sand- paper or
5.Place a nut and brass female (fr'om compression el- bow fittings) onto both pipe ends. Connect elbows to the sink cold water pipe as shown below,
TO SINK
COLD FAUCET
nut (,t) _t_
brass ferrule (,t)
|
| bTs ferrule |
elbow (2) '"_' |
|
|
| • | adaptor |
|
| FILTER |
| HOUSING | |
| nut | compression |
| to sink |
|
shutoff |
|
|
v"flve "_'_( | ) |
|
|
| continued |
5