Option Selections
You can customize your cycles by pressing an option. If you change your mind, press the option again to turn the option off. Select a different option if desired.
You can change an option anytime before the selected option begins. For example, you can press an unheated drying option anytime before drying begins.
Press START/RESUME to use the same cycle and option(s) as the previous wash cycle.
NOTE: If the last cycle you completed was a rinse cycle, when you press START/RESUME, the dishwasher runs the last full wash cycle and options.
Hi Temp Wash
Select this option to heat the water to 140ºF (60ºC) during parts of the cycle. Heating the water helps improve washing results. This option adds heat, water and wash time to parts of the cycle. Hi Temp Wash is useful when loads contain tough food soil items.
NOTES:
■Pots Pans automatically uses this option. Hi Temp Wash is an option with the Heavy Wash and Normal Wash cycles.
■Use this option for heavier than
If you press any pad while your dishwasher is locked, the light flashes 3 times.
NOTE: If the Heated Dry option is selected, the light will temporarily turn off until Lock On glows.
To turn off the Lock
Press and hold HEATED DRY for 4 seconds. The light turns off.
Delay Hours
Select this option to run your dishwasher at a later time or during
To delay the start
1.Press the delay button to choose the number of hours delayed.
2.Select a wash cycle and options.
3.Press START/RESUME.
The dishwasher starts the cycle in the selected number of hours.
NOTES:
■To cancel the delay and cycle, press CANCEL/DRAIN.
■To cancel the delay and start the cycle, press START/ RESUME.
Sani Rinse
Select this option to raise the water temperature in the final rinse to approximately 155°F (68°C). Sani Rinse adds heat and time to the cycle. This
NOTE: Sani Rinse is an option with Pots Pans, Heavy Wash and Normal Wash. Only these sanitization cycles have been designed to meet the NSF/ANSI requirements.
Heated Dry
The Heated Dry option in combination with rinse aid will give you excellent drying results. The energy to use Heated Dry costs pennies per cycle. Heated Dry is on when the light is lit on the Heated Dry button. Be sure to load plastic items in the upper rack to avoid damage.
You may turn off the Heated Dry option by pressing HEATED DRY so that the light goes off. However, you will have items in your dish load that will not be dry at the end of the cycle.
NOTE: The Heated Dry option is used in all cycles except Quick Rinse.
Lock On
Use the Lock On to prevent unintended use of the dishwasher. You can also use the lock feature to prevent unintended cycle or option changes during a cycle.
When LOCK ON is lit, all buttons are disabled.
NOTE: The dishwasher door can be opened while the controls are locked. However, the lock must be turned off and the Start/ Resume button pressed to resume the cycle.
To turn on the Lock
Press and hold HEATED DRY for 4 seconds. LOCK ON glows.
Cycle Status Indicators
Follow the progress of your dishwasher with the Cycle Status indicators.
NOTE: The features on your dishwasher may vary from those shown here.
Clean
Clean glows when a cycle is finished. The light turns off when you press any button or close the door.
Sanitized
If you select the Sani Rinse option, Sanitized glows when the Sani Rinse cycle is finished. If your dishwasher did not properly sanitize your dishes, the light flashes at the end of the cycle. This can happen if the cycle is interrupted or the incoming water temperature is too low. The light turns off when you press any button or close the door.
Drying System
During drying, you can see steam escaping through the vent at the upper left corner of the door. This is normal as the heat dries your dishes.
IMPORTANT: The vapor is hot. Do not touch the vent during drying.
13
