OCCURRENCE | POSSIBLE CAUSE | SOLUTION |
WASHER - OPERATING (continued)
Washer does not start Cycle selector is not in correct position.
(continued).
Motor is overheated.
Move indicator clockwise slightly. Pull out knob.
Washer motor will stop if it becomes overheated. It will automatically restart after a cool down period of up to 30 minutes (if washer has not been manually turned off).
Washer won't spin. | Lid is not completely closed. | Close lid completely. Safety lid lock must not be broken. | ||||
|
|
|
|
|
| |
Residue left in tub. | Heavily soiled items. | Wipe tub with a nonabrasive household cleanser, then | ||||
|
|
|
| rinse. Shake or brush excess dirt and sand from items | ||
|
|
|
| before washing. | ||
|
|
|
|
| ||
| WASHER - WATER |
|
|
| ||
Wash load too wet after | Washer is overloaded. | Do not overload washer. See Washing Procedures. | ||||
spin. |
|
|
| |||
Load is out of balance. | Rearrange load to allow proper spinning. | |||||
|
|
| ||||
|
|
|
|
|
| |
|
|
| Drain hose is kinked. | Straighten drain hose. | ||
|
|
|
|
|
| |
Water does not enter | Lid is not completely closed. | Close lid completely. Washer will not fill with water when | ||||
washer or it enters slowly. |
| the lid is open. | ||||
|
|
|
|
| ||
|
|
| Water supply is not adequate in area. | Check another faucet in the house. Wait until water | ||
|
|
|
| supply and pressure increase. | ||
|
|
|
|
| ||
|
|
| Water supply faucets are not completely open. Fully open hot and cold faucets. | |||
|
|
|
|
| ||
|
|
| Water is being used elsewhere in the house. Water pressure must be at least 30 psi (260 kPa). Avoid | |||
|
|
|
| running water elsewhere while washer is filling. | ||
|
|
|
|
| ||
|
|
| Water inlet hoses are kinked. | Straighten hoses. | ||
|
|
|
|
| ||
Water level does not cover | Washer is overloaded. | Do not overload washer. When control is set at highest | ||||
load. |
| fill level, dry load level should not be higher than top row | ||||
|
|
|
| of circular holes in wash tub. | ||
|
|
|
| |||
Warm or hot water is not Hot water heater is set too low or is a | Measure hot water temperature at nearby faucet with | |||||
hot enough. | distance from laundry center. | candy or meat thermometer. Water temperature should | ||||
|
|
|
| be at least 120°F (49°C). Adjust water heater as necessary. | ||
Hot water is being used elsewhere in the house.
Avoid using hot water elsewhere before or during washer use. There may not be enough hot water available for proper cleaning. If problem persists, your hot water system may be unable to support more than 1 use at a time.
| To conserve energy, the temperature of | See Operating Instructions for your washer | ||
| the hot wash is regulated. |
|
|
|
|
|
|
|
|
Water in washer does not | Drain hose is kinked or clogged. | Clean and straighten the drain hose. | ||
drain or drains slowly. |
|
|
|
|
|
|
|
|
|
Water leaks. | Loose fill hose connection at faucet or | Check and tighten hose connections. Install rubber sealing | ||
| washer. | washers provided. | ||
|
|
|
| |
| House drain pipes are clogged. | Unclog drain pipes. Contact plumber if necessary. | ||
|
|
|
| |
| Oversudsing. | Use less detergent. | ||
|
|
|
|
|
Incorrect wash and rinse | Hot and cold water hoses are connected | Connect hot water hose to hot water faucet and cold | ||
temperatures. | to wrong supply faucets. | water hose to cold water faucet. | ||
|
|
|
| |
Water is entering washer | Drain hose standpipe is incorrect height. | Standpipe must be a minimum of 33" (83.82 cm) high to | ||
but tub does not fill. |
| prevent siphoning. See INSTALLATION INSTRUCTIONS. | ||
13
