SECO-LARM USA EV-122C-DXA3 instruction manual Specifications, Parts List, Dimensions

ENFORCER BALL-MOUNTIR DOME CAMERA Manual

ENFORCER BALL-MOUNTIR DOME CAMERA Manual

Specifications	EV-122C-DXA3 (NTSC)
Type	Color camera
Chip	1/3” CCD, Sony
Resolution	420 TV lines
Pickup elements	510 x 492 pixels
Scanning system	2:1 interlace, V: 59.94Hz, H: 15.734KHz
Sync	Internal

EVA-F5521-3 -- Optional power cord. For easy connection of dome or bullet camera to power supply.

	To BNC
	(3-ft. wire length)
(From DC	(EVA-F5521-3)
Camera)

Parts List

1 x Camera Ball

1 x Case (2-part construction)

1 x Base

3 x Screws

1 x Manual

Video output	1V pp composite output, 75 ohms
Lens	F1.2, 3.6mm (lens included)
IR LEDs	24 x LEDs
IR distance	Up to 50’ (15m)
IR view angle	50o~80o beam spread, 30o per LED
Minimum illumination	0.05 lux, (0 lux with IR on)
Gamma correction	0.45
S/N ratio	>50dB
Shutter control	Auto Electronic Shutter (AES), 1/60~1/100,000 sec.
Backlight compensation	Auto
Automatic gain control	Auto
White balance	Auto, 2500o ~ 9500oK
Power source	12VDC ±10%
Power consumption	70mA (IR off), 280mA (IR on)
Storage temperature	-22°~140° F (-30°~60° C)

Power

3 xConnector

Screws

BNC

Connector

	Case	Camera
Case		Ball	Base

Operating temperature	14°~122° F (-10°~50° C)
Dimensions	311/16” x 211/16” (93 x 69mm)
Weight	6.3 oz. (180g)
Dimensions:

BEFORE STARTING

1.Please read this manual carefully and keep it for future reference.

2.Use the camera within given temperature and electrical limits.

3.Do not mount the camera where it is exposed to rain or other moisture, or in humid or dusty places.

4.Do not point the camera at the sun. Heat could damage the camera, even when not in use.

5.Do not mount the camera in areas exposed to radiation, strong magnetic fields, or strong electrical signals.*

6.Do not open or disassemble the camera. There are no user- serviceable parts inside.

7.Do not drop the camera or subject it to strong vibrations.

*Note: Many video monitors produce strong electromagnetic fields close to the display CRT, especially when the monitor is turned on or during de-Gaussing, which occurs automatically with many monitors when the monitor is turned on.

211/16”

(69mm)

311/16” (93mm)

INSTALLATION

1.Run a 12VDC power supply wire and a video cable with a male BNC connector through the wall to where the camera is to be mounted.

2.Temporarily connect the camera to the 12VDC power supply.

3.Temporarily connect the camera’s female BNC connector to the video cable’s male BNC connector.

4.While watching the monitor, hold the camera against the wall by hand where it is to be mounted, then turn the camera until it is certain that this mounting location is correct. Use a pencil to mark the location of the three screw holes in the base.

5.Disconnect the 12VDC power supply and video cable.

6.Mount the bracket to the wall using the three included mounting screws. If the wall is made of dry wall, brick, or similar material, it may be necessary to use screw anchors (not included).

7.Reconnect the 12VDC power supply and video cable. Turn the monitor on, and make sure the camera is sending the proper video signal.

8.Adjust the camera angle.

9.Put the case over the camera ball and twist to secure to the base.

10.Do a final test of the video camera and monitor.

*Note: The base also allows flush-mounting of the camera. However, for the best security, run the wires through the wall.