ENFORCER CCD IR DAY/NIGHT CAMERA MANUAL
Specifications |
|
|
| ||
|
|
|
Type | Color camera | B/W camera |
|
|
|
Chip | 1/3” CCD, Sony | 1/3” CCD, Samsung |
|
|
|
Resolution | 420 TV lines | 420 TV lines |
Pickup elements | 1/3” CCD | 1/3” CCD |
| 512 x 492 pixels | 512 x 492 pixels |
|
|
|
Scanning system | 2:1 interlace | 2:1 interlace |
|
|
|
Sync | Internal | Internal |
|
|
|
Video output | 1V pp composite output, 75 ohms | 1V pp composite output, 75 ohms |
|
|
|
Lens | F1.8, 4.3mm (lens included) | F1.8, 4.3mm (lens included) |
|
|
|
Minimum illumination | 0.1 lux (LED off), 0.0 lux (LED on) | 0.1 lux (LED off), 0.0 lux (LED on) |
|
|
|
Gamma correction | 0.45 | 0.45 |
|
|
|
S/N ratio | >50dB (AGC off) | >48dB (AGC off) |
|
|
|
Shutter control | Auto Electronic Shutter (AES) | Auto Electronic Shutter (AES) |
| 1/60~1/100,000 sec. | 1/60~1/100,000 sec. |
|
|
|
Backlight compensation | auto | auto |
|
|
|
Automatic gain control (AGC) | auto | auto |
|
|
|
Enclosure | IP67 weatherproof | IP67 weatherproof |
# of infrared LEDs | 12 | 12 |
|
|
|
Max. LED range | Up to 40 ft. | Up to 40 ft. |
ENFORCER CCD IR DAY/NIGHT CAMERA MANUAL
A. Camera |
|
| F. BNC connector (female) |
|
| Parts List | |||
B. Adjustable Sunshield | G. Adjustment nut |
|
| 1 x IR camera | |||||
C. Mounting bracket | H. Mounting holes |
|
| ||||||
B | 1 x Sunshield | ||||||||
D. 36” cord |
|
|
| ||||||
|
|
| 1 x Mounting bracket | ||||||
|
|
|
|
| |||||
E. DC jack |
|
|
|
|
| ||||
|
|
|
|
| 3 x Mounting screws | ||||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| 3 x Screw anchors | |
F |
|
|
| E |
|
|
| 1 x Manual | |
|
|
|
|
| |||||
|
|
|
|
|
|
| ® |
|
|
|
|
| |
|
| Infrared | ENFORCER | ||||||
|
| Day/Night |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| A |
|
|
|
|
|
|
|
|
| |
D |
|
|
|
| G | ||||
|
|
|
| ||||||
|
|
|
|
|
|
| |||
C |
|
|
|
| Hx3 | ||||
|
|
| |||||||
|
|
|
|
| |||||
|
|
|
|
|
Power source | 12VDC±10% | 12VDC±10% |
Power consumption | 60mA (IR off), 160mA (IR on) | 110mA (IR off), 210mA (IR on) |
Operating temperature | 14°~131° F | 14°~131° F |
Dimensions | 31/16”(L) x 21/4”(D) (78 x 57 mm) | 31/16”(L) x 21/4”(D) (78 x 57 mm) |
| (without sunshield) | (without sunshield) |
|
|
|
Weight | 16 oz. (454g) | 16 oz. (454g) |
BEFORE STARTING
1.Please read this manual carefully and keep it for future reference.
2.Use the camera within given temperature and electricity limits.
3.Do not aim the LED light directly at the eyes when the LEDs are on.
4.Do not point the camera at the sun. Heat could damage the camera, even when not in use.
5.Do not mount the camera in areas exposed to radiation, strong magnetic fields, or strong electrical signals.*
6.Do not open or disassemble the camera. There are no user- serviceable parts inside.
7.Do not drop the camera or subject it to strong vibrations.
*Note: Many video monitors produce strong electromagnetic fields close to the display CRT, especially when the monitor is turned on or during
Dimensions:
21/4” (57mm)
211/16” (68mm)
29/16” (65mm)
ENFORCER® Infrared
Day/Night
31/16” (78mm)
9/16” (14.5mm) 113/16” (46mm)
INSTALLATION
1. Run a 12VDC power supply wire and a video cable with a male BNC connector through the wall to where the camera is to be mounted (if necessary).
2.Assemble the mounting bracket; then screw it into the back of the camera. Make sure the mounting base is tightened to the bracket.
3.Temporarily connect the camera to the 12VDC power supply.
4.Temporarily connect the camera’s female BNC connector to the video cable’s male BNC connector.
5.While watching the monitor, hold the camera bracket against the wall by hand where it is to be mounted, then twist the camera until it is certain that this mounting location is correct. Use a pencil to mark the location of the three screw holes in the bracket.
6.Disconnect the 12VDC power supply and video cable.
7.Mount the bracket to the wall using the three included mounting screws. If the wall is made of dry wall, brick, or similar material, it may be necessary to use the three included screw anchors.
8.Reconnect the 12VDC power supply and video cable. Turn the monitor on, and make sure the camera is sending the proper video signal.
9.Adjust the camera angle:
(a)Loosen and tighten the bracket’s thumb screw to turn the camera and change its angle relative to the bracket. This ensures the camera is pointing in the right direction.
(b)Loosen and tighten the adjustment plate to rotate the camera on its axis. This rotates the angle of the video image.
10.Tighten the bracket’s thumb screw and the adjustment plate so that the camera does not move, but not so tight that it cracks the case or bracket.
11.Do a final test of the video camera and monitor.