Sennheiser MD419 Directionaleffect, 7 N, 1',2, KA 7 U, Cannon male connector, with 3 prong connector, For all Senn heiser micro, a Cannon female connector, N-T, U-T, MD419

Four versions of the MD 419 are available:

MD 419 N 3-pin plug (small Tuchel plug, screwable); low impedance, balanced. (Fig. 1)

MD 419 U 3-pin Cannon plug (XLR); low impedance, balanced. (Fig. 1)

MD 419 N-TSame as MD 419 N, but with on/off switch MD419 U-TSame as MD 419 U, but with on/off switch

Connecting the microphone

For connection of the MD 419 to your tape-recorder the following connecting cables are available:

phones show this increase of low frequencies at dose miking. With the bass filter (Fig. 2) set to position "S" the accentuation of the low frequencies can be eliminated. Therefore, the switch should always be set to position "S" when the distance between mouth and sound source is less than 20 cm. If the distance is more than 20 cm the switch should be set to the middle position. For recordings from a greater distance or when recording music switch position "M" is preferable.

Directionaleffect

The MD 419 features a pronounced directionality, which is called

r	,
~T	~
3261001	Mas30
(Art No.0024)

Connecting Cable DA 7 NConnects alilow impedance dynamic microphones fittedwith 3 prong connector.The 7.5 metre 2 lead shielded

cable is fitted with a coupling (e. g. T 3261001) and a male connector (e. g. Mas 30).

with a length of 7.5 meters. Connects balanced, low impedance microphones to amplifiers with medium impedance inputs. Jack plug at one end, 3-pin DIN coupling at the other.

k:J2L	LQ-~1
T 3261001	Mas30
(Art.No.0890)

super cardioid. The microphone "hears" best in a forward direction and gets more and more "deaf" towards the sides and the back. Therefore the microphone must always be directed towards the sound source wh ich is to be recorded. Due to the pronounced directionality disturbing noise coming from the sides and from the back are effectively suppressed. Signals reaching the microphone diagonally from the back (120°) produce only 1',2(22 dB) of the voltage which would be produced bya signal reaching the microphone directly from the front. Due to this

characteristic the MD 419 is especially suitable for recordings in acoustically unfavourable environments.

Mounting the microphone

Whether your floor stand is equipped with a 3/8"-, '/2" or a 5/8" x

~rYj

T 3261001Mas30 (Art.No.0025)

Connecting Cable DA 7 NL

Connects low impedance bi:llanced (N) microphones to low impedance unbalanced inputs (L). Coupling as per DIN 41524 (e. g. Tuchel

T 3261 001) and 3 prong male connector (e. g. Mas 30).

Connecting Cable DA 7 NM

Intended for use with low

impedance balanced microphones fitted with 3 prong connector as per DIN 41524. The 2 lead shielded cable is fitted with the connector

Mas 30 and a coupling Tuchel T 3261 001.

~L	~-~
XRL-3-11C	XRL-3-12C
(Art. No. 1777)

27 G thread, the MD 419 with its quick release clamp will fit them all. The quick release clamp (Fig. 3) is equipped with achanging thread, which can be unscrewed with a coin. For the adaptation to '/2" threads the insert has to taken out, turned around and replaced. If the insert is removed completely the clamp will fit %" x 27 G threads.

Aeoustleal mode 01 operation			. pressure gradient			transdueer
Frequeney	response		30	..15000Hz
Doreetlonal	pattern	.	super eardioid
Rejeetionat 1kHz and 1200 :t 100			22 dB
Sensitlvity	at 1 kHz		. 1,3 mV/Pa:t		2,5	dB
Eleetrieal impedanee		al 1 kHz	.20012
Min. load impedanee		.	100012
Conneetors:	MD419	N	. 3-pin	plug	10 DIN	41 524
	MD 419	U	. 3-pin Cannon XLR-3

r	,	Connecting Cable KA 7 U
		For all Senn heiser micro-
1,	I	phones with the suffix U. The
	I
	~ J	cable is fitted on one end with
~1	~ J	cable is fitted on one end with
T 3261001	Jack Plug 6,3 mm0	a Cannon female connector,
(Art. No. 1496)		and on the other end with a
		and on the other end with a
Connecting Cable DA 7 NK		Cannon male connector
Two-conductor shielded cable		XLR-3. Length of cable: 7.5 m.
		XLR-3. Length of cable: 7.5 m.

If none of the connecting cables listed fits to the microphone input of your set, please contact your RN-dealer.

Bass filter

Hold the microphone on arms length and bring it slowly back towards your mouth. If you listen to your own voice via a headphone you will realize that your voice sounds more dull the closer the microphone gets towards your mouth. All directional micro-


Wiring:	MD 419 N		1 and 3 ~	signal
	MD 419 U		2 + housing ~		ground
	MD 419 U		2 and 3 ~	signal,
Dimensions In mm			1 + hauslOg~		ground
Dimensions In mm			190 x 45 x 45
Weight	. . . .	...	. approx. 1809

We reserve Ihe fight to alter speclflcallons, In partlcular wlth regard 10fechnlcal improvements.

Recommended accessoriesWindscreen MZW 40This sponge windscreen efficiently suppressespopping noise at close miking. Indispensable for outdoor recordings.