ACCESSORIES

Power supplies

Cables

Windshield MZW 30

The foam-rubber-windshield

should be drawn over the sound

inlets of the microphone when wind disturbances are evident.

Largest diameter: 60 mm

Length: 80 mm, Reduction of

wind disturbance: approx.20 dB.

Shock mount MZS 415
Swivel mount MZG 415

The swivel mount gives the possibility to use the desk stand together with the microphone

clamp or the shock mount for the MKH 406 T

Desk stand MZT 441
The MZT 441 is together with the swivel mount MZG 415 and
Power unit MZN 16 T and T-U

For simultaneous powering of two microphones. Connection to 220 volt or 110 volt supplies. The unit can be included in the

microphone cable at any point. Model T-U with Cannon connectors.

Dimensions in mm:

168 x 120 x 50.

Connecting cable KA 1 and KA 7
Tripie conductor screened cable. Fitted with 3 pin connectors according to DIN 41524.KA 1: 1.5 m long,KA 7: 7.5 m long

The shock mount can be connected to all tripods, booms, etc. with 3/8" threads and prevents recordings being disturbed by footfall or other strong mechanical disturbances. Diameter: 35 mm. Length: 80 mm.

Microphone clamp MZQ 415
The clamp can be fitted on tri-pods, booms etc. with 3/8" threads.

Battery adapters

Battery adapter MZA 15 Can be connected into the

microphone line at any point. Fitted with 9 mercury cells Mallory RM 625, it provides a continuous operation for 50 to 60 hours. The mercury cells can be purchased in allshopswithcater for the hard of hearing. Special feature: If the plug and connector are connected together the battery condition is indicated by a built-in LED. To prevent an unnecessary discharge of the batteries, the battery adapter should be

unscrewedfrom the microphone when it is not in use.

Dimensions in mm: 220 x 132.

the microphone clamp MZQ 415 or the shock mount MZS 415 astable desk stand for theMKH 4061.
Desk stand MZT 100

A stable desk stand with good

handling noise suppression. For use with the MKH 406 T the MZT 100 is to be combined with the swivel mount MZG 415 and

the microphone clamp MZQ 415 or the shock mount MZS 415.

Battery adapter MZA 15-U

Same as MZA 15, however fitted with Cannon connector XLR-3-11 C

and plug XLR-3-12 C for use with the MKH-U types.

Dimensions in mm: 22 0 x 152.

Auxiliary units

Transistor amplifier KAT 15-2 For the connection of condenser

microphones, or symmetrical low impedance dynamic microphon es, to the line and accessory inputs respectively, of the Nagra 111or Nagra IV. Selected functions:

T = condenser microphones

N = dynamic microphones

A switchable footfall filter is in- cluded.

Dimensions in mm: 85x40x25.

Roll-oft-filter MZF 15

The roll-oll-filter MZF 15 should be included only between supply voltage source and amplifier input.

Frequency reduction

at 50 Hz approx. 6dB at 25 Hz ~ 15 dB

Dimensions in mm: 220x152.

Connecting cable KAM 1-5 For the connection of series 6

microphones to the "Microport" transmitters SK 1006, SK 1007, SK 1008 and the SER 1. The

microphones are powered from the transmitter.

KAM 1-5: 1 m long.

Connecting cable KA 7 U

For use with all Sennheiser micro-

phones with the sullix U. The KA 7-U is fitted on one end with

a Cannon female connector,

and on the other end with a Cannon

plug (XLR-3-12 C). Cable length: 7.5 m

12

13