Shark S3325W, S3325R owner manual Operating Instructions

OPERATING INSTRUCTIONS

Filling your Canister Steam Cleaner with Water

IMPORTANT: Always insure that the unit is UNPLUGGED from the wall receptacle and all switches are in the "Off' position prior to initial filling or re-filling til e water tank . Never attempt to fill this unit under a water tap, always use the filling flask and funnel provided. Failure to follow these steps will cause the water tank to overfill and may pose an electrical safety hazard.

RECOMMENDATION : The use of distilled/demineralized water is recommended, particularly in areas with hard water in order to prevent the build-up of lime scale .

Step 1: Press the safety cap down and turn counter clockwise until removed .

Step 2: Assure that the steam cleaner is empty so that the addition of the prescribed amount of water will not result in overfilling.

Step 3: Add 47 fl. oz (1400 ml) of water using the filling flask and funnel provided. (Fig. 1) Do not overfill. Replace safety cap by turning clockwise - press down firmly to tighten. Heating time is approximately 8-10minutes . Fill:ng the boiler with hot water will shorten heat up time.

Step 4: Connect the desired accessory onto the steam hose.

Step 5: Plug the unit into a standard 120 volt wall receptacle. Press the On/Off switch. The Heating light (Red) will light up.

Step 6: Allow approximately 8-10minutes for water vapor to reach its working temperature. When the unit is ready for use the steam ready light will light up.

Step 7: Upon initial use, some water will come out from the hose nozzle. This is residual water that is left over in the hose from the last use and is normal.

Jt.. CAUTION: Always point the

.... nozzle outlet in a safe direction .

Never point in the direction of ourself. other people or pets.

-~

Fig. 1

NOTE: When the steam cleaner has run out of water, steam output will cease.

Refilling Unit Wah Water

Jt.. WARNING : Always allow the

.... unit to cool for 15 minutes

before re-filling. When re-filling the steam cleaner while it is still hot, the first drops of water might bubble up . Use caution when opening the safety cap as cap may become hot during use and escaping steam can cause scalding.

Step 1: Press the On/Off button on the unit to the "Off' position .

Step 2: Press the On/Off steam switch to the "On" position and wait until no more steam comes out of the hose.

Step 3: Remov e the plug from the electrical outlet and allow the unit to cool for approximately 15 minutes before refilling with water .

Step 4: After completing the cool down period of step 3 (above), carefully press down on the safety cap and turn counter clock wise to loosen.

Step 5: Slowly pour water using the filling flask and funnel provided into the boiler. DO NOT fill under a faucet. Always use the filling flask and funnel that are provided . DO NOT OVERFILL. Never put more than 47 ounces (1400 ml) of water in the unit at one time.

Step 6: Screw safety cap back on to the unit by turning clockwise and press down to tighten securely. Plug appliance back into wall outlet. Steam will start to be produced as before.

Using Your Steam Cleaner with

Steam Pocket

Step 1: Connect one of the extension tubes to the hand grip on the flexible steam hose . To attach the extension tubes one onto the other or onto the hand grip , press the locking button ensuring that it fits into the hole. (Fig. 2) To disconnect, repeat the operation by pressing the locking button and pulling the two sections apart.

Fig."2 ~,

NOTE: Fit the stearn pocket frame with the angle adapter onto the extension tube.

Step 2: If the angle adapter is not attached to the steam pocket frame, attach as follows: Hold the steam pocket

frame in one hand and the angle adapter in the other. Insert the angle adapter

stem into the- Fig. 3 opening of the steam pocket frame as shown in Fig. 3.

Note that the flat on the nozzle must face toward the side of the fram e with the brass pin. Once inserted, rotate it 90°.

Attaching the Steam Pocket Towel to the Frame

Jt.. WARNING: Always insure the

.... unit is UNPLUGGED from the wall

receptacle prior to attaching or removing accessories.

1.Slide the steam pocket towel over the steam pocket frame. (Fig. 4 )

2.Bring the towel all the way to the top of the steam pocket fram e. (Fig. 5)

3.Bring the velcro strips that are on the back side of the steam pocket towel over the steam pocket frame and attach to the inside of the front side of the steam pocket towel. (Fig. 6)

5 6