SHARK SSG • 8.914-337.0 / 97-6134 • Rev. 8/07
33
PRESSURE WASHER OPERATOR’S MANUAL
AR-AL UNLOADER ExPLODED vIEW AND PARTS LIST

AR - AL 607 #9.802-367.0, 7-8 Gpm, 4200 Psi

ITEM PART NO. DESCRIPTION qTy
1 8.718-371.0 Check Connector 1
2 9.804-536.0 ‡ O-Ring 2068 3
3 9.804-646.0 Shutter Spring 1
4 9.804-538.0 Shutter 1
5 9.804-539.0 ‡ O-Ring 631290 SH 1
6 83-005170102 1/4 G Plug 1
7 83-005030101 M8 Lock Nut 1
8 83-005100100 Knob 1
9 83-005150101 Washer 1
10 83-005400403 4000 PSI Spring (Black) 1
11 83-005150011 Stem Guide Union 1
12 9.804-588.0 ‡ Back Ring 2
13 9.804-589.0 ‡ O-Ring 2031 1
14 83-005160502 Stem AL606 1
14 83-005160514 Stem AL607 1
15 83-005106301 Spring Pin 1
16 83-005000101 Back Ring 2
17 9.804-590.0 ‡ O-Ring 2050 1
18 83-005020003 Body By Pass 1/4 G-F 1
18 83-005020026 Body By Pass 3/8 G-F 1
19 83-005060200 3/8 Gasket 1
20 9.804-591.0 ‡ O-Ring 2043 1
21 9.804-592.0 ‡ Seat 1
22 9.804-593.0 ‡ Ball 1
23 8.718-370.0 Ball Spring 1
24 83-005150009 Seat Union 1
25 83-005030200 M8 Nut 2
26 83-005170101 3/8G Plug 2
27 83-005060201 Gasket 1
83-005650200 ‡ Repair kit

Unloader Adjustment Procedures

Remove lock nut (Item 7).
Remove adjustment knob (Item 8).
Loosen the two (2) nuts (Items 25), move them upward on stem (Item 14) until you see 4 or more threads below the nut.
Re-attach adjusting knob (Item 8).
Start machine. Open the trigger of the spray gun. Increase pressure by turning adjustment knob (Item 8) clockwise until
pressure is at the desired operating pressure.
Remove the adjustment knob (Item 8), tighten the lower nut (item 25) tightly against the upper nut (Item 25). Re-attach
adjustment knob (Item 8) and screw down until contact is made with the nuts (Item 25). Screw down lock nut (Item 7)
onto the stem (Item 14) until the threads cut into the nylon insert of the lock nut (Item 7).
*If adjustment knob (Item 8) DOES NOT make contact with upper nut (Item 25), remove adjusting knob (Item 8), re-adjust
(raise) nuts (Items 25) on stem (Item 14) and re-attach adjustment knob (Item 8), then repeat step #6.
**If adjustment knob (Item 8) DOES make contact with upper nut, release the trigger of the spray gun and watch the pressure
gauge for the pressure increase (“spike”). This “spike” ShOULD NOT exceed 500 psi above the operating pressure. If spike
pressure exceeds the 500 psi limit, remove the adjusting knob (Item 8) and re-adjust (lower) the nuts (Items 25) on the stem
(Item 14). Re-attach the adjusting knob (Item 8), then repeat step #6.
1.
2.
3.
4.
5.
6.
24
2
23
22
21
20
1
2
3
4
5
27
6
26
19
6
14
16
17
16
18
13
12
2
15
25
7
9
10
11
8
26