Shark SV736R, SV736N Battery Pack Replacement & Disposal, Wall Mounting Bracket Optional, Problem

Fig. 8

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

Battery Pack Replacement & Disposal

Your Cordless Vacuum is powered by Nickel-Cadmium Ni-Cd) batteries, which must be recycled or disposed of properly in accordance with state, federal and local laws.

If uncertain as to how to remove the battery pack, we suggest you take your hand vacuum to a reputable small appliance service technician to have this service preformed.

Do NOT attempt to replace the batteries used in this product with any other type of battery.

The battery pack of your cordless vac is replaceable, however care should be taken when doing so. Follow these steps when replacement is required:

1.Using a #1 Phillips head screw driver, remove the single screw securing the battery compartment cover located on the under side of the unit.

2.To remove the cover, press down on the battery compartment cover while sliding towards the rear of the unit.

NEVER open the battery compartment except to change the battery.

3.Set aside battery compartment cover and screw.

4.Lift off the battery strap and set aside.

5.Carefully lift out the top battery pack

(A)and disconnect the terminals. Then remove the single battery (B) that is on the bottom and disconnect the terminal. (Fig. 8)

6.Connect the terminals to the single battery (B) first and insert into the new unit. Then connect the terminals to the battery pack (A) taking care to connect the black leads (-) to the negative connectors first and the red leads

(+) to the positive connectors second. Place the new battery

(A)into the battery

compartment.

7.Tuck the wiring inside the battery compartment so that the wiring does not interfere with the battery compartment cover when it is replaced.

8.Re-install the battery strap and battery compartment cover.

5

WARNING: NEVER use ordinary batteries for replacement, as these may leak and damage your vacuum cleaner. Use only battery pack XBP736 provided by EURO-PRO Operating LLC for replacement.

CAUTION: NEVER use the unit without the battery compartment cover in place.

NOTE: Any other servicing should be performed by an authorized service representative.

CAUTION

•Use only with the battery pack supplied with the unit.

•Do not attempt to remove the battery pack from the unit to charge it.

•Never attempt to throw the battery pack or unit into a fire or incinerate it.

•Do not attempt to remove or damage the battery casing.

•Battery must be recycled or disposed of properly at the end of it's service life.

•Do not place batteries on metal surfaces.

•Do not touch metal parts of the batteries together as the batteries will overheat.

Wall Mounting Bracket (Optional)

1.Make sure that the intended wall area for the wall mounting bracket to be drilled is free from any hidden electrical wires, water pipes and gas lines.

2.Select an appropriate place close to a wall power outlet (120V., 60 Hz).

3.Do not mount near direct sunlight, near a heat source or outdoors.

4.Select an appropriate drill type for the material to be drilled.

5.Carefully measure and mark the location of all bracket holes and then drill holes and screw the wall mounting bracket onto the wall.

TROUBLESHOOTING GUIDE

PROBLEM	POSSIBLE REASON		POSSIBLE SOLUTION
	1. Batteries discharged.		1. Charge unit.
HAND VACUUM	2.	Dead battery (battery	2.	Replace batteries. (See
		won't hold charge).		page 5.)
WILL NOT
	3.	No power in electrical	3.	Check fuse or breaker.
OPERATE
		outlet supplying		Replace fuse/reset
		transformer.		breaker.
	1.	The 2 metal pins of	1.	Firmly insert the
				motorized brush into the
		the motorized brush
				air-intake nozzle. This
MOTORIZED		are not in contact
				will connect the
BRUSH WILL NOT		with the vacuum
				motorized nozzle to the
WORK		cleaner.
				unit power supply.
	2.	Motorized brush is
			2. Remove all lint, hair etc.
		clogged up.
				from motorized brush.
	1.	Dust cup container is	1.	Empty dust cup
				container
		full.
HAND VACUUM			2.	Remove dust cup filter
	2. Dust cup filter needs
WILL NOT PICK-				and check for object(s)
		cleaning or
UP OR SUCTION				in air duct and remove.
		replacement.
POWER IS WEAK				Clean or replace dust
	3.	Unit needs
				cup filter.
		recharging.
			3.	Charge unit.
	1. Dust cup container is		1.	Empty dust cup
		full.
DUST ESCAPING				container.
	2. Dust cup filter is not
FROM HAND			2.	Review dust cup filter
		installed correctly.
VACUUM				installation instructions.
	3.	Puncture/hole in dust
			3. Replace dust cup filter.
		cup filter.

6