Sharp AR-M201 5, ENVIRONMENTAL INFORMATION

5ENVIRONMENTAL INFORMATION

The products that meet the ENERGY STAR

guidelines carry the logo shown above.

The products without the logo may not meet the ENERGY STAR® guidelines.

Products that have earned the ENERGY STAR® are designed to

protect the environment through superior energy efficiency.

A small amount of ozone is produced within the unit during operation. The

emission level is insufficient to cause any health hazard.

Note:

The present recommended long term exposure limit for ozone is 0.1ppm

(0.2mg/m3) calculated as an 8 hr. time-weighted average concentration.

However, since the small amount that is emitted may have an objectionable odor, it

is advisable to place the unit in a ventilated area.

!000-Cautions.fm 5 ページ２００８年３月５日　水曜日　午後２時１８分

Contents

Main AR-M201 Page CONTENTS 1PREPARATIONS 2LOADING PAPER 3MAKING COPIES 4CONVENIENT COPY FUNCTIONS 6PRINTER/SCANNER FUNCTIONS 7USER SETTINGS 8TROUBLESHOOTING AND MAINTENANCE 9OPTIONAL EQUIPMENT 10 APPENDIX 3 CAUTIONS (4") Caution label on the machine Cautions on using the machine 4 Cautions on handling the machine Trademark acknowledgements SOFTWARE LICENSE 5 ENVIRONMENTAL INFORMATION 6 INTRODUCTION Using the manual About the operation manuals Operation Manual (this manual) 7 MAIN FEATURES A Sort copy Offset function 2 IN 1 copy Margin shift Page 9 1 PREPARATIONS This chapter provides basic information that you should know before using the machine. PART NA MES Operation panel READY TO COPY. 100% A4 0 Display 12 CONNECTING THE POWER CORD 1 2 POWER ON AND OFF Power on Power off Power save modes Preheat mode Auto power shut-off mode Check original cover/RSPF open function LOADING PAPER PAP ER For best results, use only SHARP recommended paper. LOADING PAPER 15 1 and pull the paper tray out until it stops. 2 3 17 BYPASS FEED (including special paper) Important points when inserting paper in the bypass tray Envelopes Available Not Available 1 2 3 19 CHANGING A TRAY'S PAPER SIZE SETTING 1 2 3 4 20 MAKING COPIES NORMAL COPYING 2 1 3 1 2 1 2 3 4 Page MAKING COPIES 23 Setting the number of copies SELECTING THE TRAY Press the [TRAY SELECT] key ( ). 24 1 2 3 4 5 25 REDUCTION/ENLARGEMENT/ZOOM 1 2 3 ( ) to select the desired copy ratio and then press the [ENTER] key. 4 then press the [START] key ( ). 26 CONVENIENT COPY FUNCTIONS 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 6 1 2 3 4 31 COPYING MULTIPLE ORIGINALS ONTO A SINGLE SHEET OF PAPER 1 2 3 4 5 6 1 2 3 4 5 34 1 2 "MARGIN SHIFT" appears and then press the [ENTER] key. Page 36 5 INSTALLING THE SOFTWARE SOFTWARE MFP driver Printer driver Scanner driver 37 BEFORE INSTALLATION Hardware and software requirements 38 INSTALLING THE SOFTWARE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 INSTALLING THE SOFTWARE Connecting a USB cable 1 connector on the machine. 2 Page 5 6 7 8 Page 5 6 7 Page 6 7 8 49 6 System requirements for USB 2.0 (Hi-Speed mode) PRINTER/SCANNER FUNCTIONS 50 USING THE PRINTER MODE BASIC PROCEDURE FOR PRINTING 1 2 3 4 Cancelling a print job 1 2 51 USING THE SCANNER MODE The procedure for placing the original is the same as for copying. See "NORMAL COPYING" (p.20). 1 scanner mode. 4 The "SCAN" indicator lights up to indicate that scanner mode is selected. 2 3 52 Button Manager scan menu SCANNING FROM YOUR COMPUTER OPERATION IN COPY, PRINTER, AND SCANNER MODES 53 1 2 3 4 5 Viewing the online manual 54 USER SETTINGS USER PROGRAMS Copy mode Page Page Page Print mode 59 SELECTING A SETTING FOR A USER PROGRAM 1 2 3 4 Audible signals (key entry beep, invalid key beep, base setting beep) Base settings 61 8 DISPLAY MESSAGES TROUBLESHOOTING AND MAINTENANCE Indication Cause and remedy Page Lamp indicator Display 63 TROUBLESHOOTING THE MACHINE Page Page Page 67 PROBLEMS DURING SETUP OF THE SOFTWARE MFP driver cannot be installed (Windows 2000/XP) 1 2 3 4 Plug and play screen does not appear 1 2 3 4 The MFP driver cannot be correctly installed by Plug and Play (Windows 2000/XP/Vista) 1 2 3 4 Removing the software 1 2 3 70 MISFEED REMOVAL 1 2 A: Misfeed in the paper feed area 1 2 B: Misfeed in the fusing area 1 2 3 C: Misfeed in the transport area 1 2 3 4 r D: Misfeed in the RSPF (Option) Document feeder cover RSPF jam release leve Roller (X) (Y) 1 2 3 4 5 76 6 7 SCAN HEAD LOCKING SWITCH 77 CHECKING THE TOTAL COUNT 1 Press the [ ] key ( ) or [ ] key ( ) until "TOTAL COUNT" appears, and then press the [ENTER] key. 2 display the count of each function. MAINTENANCE REQUIRED 78 CLEANING THE MACHINE Cabinet Document glass and the back side of the original cover/RSPF Document glass/scanning window Original cover/RSPF RSPF roller RSPF scanning window Black line Page 80 9 OPTIONAL EQUIPMENT Tray SYSTEM CONFIGURATION FACSIMILE EXPANSION KIT (AR-FX13) NETWORK EXPANSION KIT (AR-NB2 A) 1 2 3 4 5 Interface cable 82 APPENDIX Page Printer Function Scanner Function Reversing single pass feeder (AR-RP9) 250-sheet paper feed unit (AR-D33) 87 INDEX Symbols [ 2 I L M N O R S T U INDEX BY PURPOSE Making copies Using convenient copy functions Connecting the computer Page Page Laser information CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT CLASS 1 LASER PRODUCT LASER KLASSE 1