Sharp CD-DH950P operation manual Enhancing your system, Troubleshooting chart

Timer and sleep operation (Remote control only) (continued)

QTo use timer and sleep operation together

Sleep and timer playback:

For example, you can fall asleep listening to the radio and wake up to CD in the next morning.

1Set the sleep time (see above, steps 1 - 5).

2While the sleep timer is set, set the timer playback (steps 2 - 10, page 12).

Sleep timer		Timer playback		End time
setting		setting
	10 - 90 minutes			Desired time
		Sleep operation will	Timer playback
		automatically stop	start time

Enhancing your system

The connection cord is not included. Purchase a commercially available cord as shown below.

Portable audio player, etc.

		PHONES
To the	TIMER
line	POWER
output	iPod/iPhone
jack	VOL.	VOL.
	(BAND)
	CD
	TUNER
	TUNING	PRESET
	USB	AUDIO IN
	AUDIO IN

PHONES

AUDIO IN

USB

Audio cable (not supplied)

QListening to the playback sounds of portable audio player, etc.

1Connect a portable audio player etc. to the front AUDIO IN jack.

2Press the ON/STAND-BY button to turn the power on.

3Press the AUDIO IN/USB button repeatedly to select

AUDIO IN.

4Play the connected equipment.

If volume level of the connected device is too high, sound distortion may occur. Should this happen, lower the volume of the connected device.

If volume level is too low, increase the volume of the connected device.

Note:

To prevent noise interference, place the unit away from the television.

QHeadphones

OBefore plugging in or unplugging the headphones, reduce the volume.

OBe sure your headphones have a 1/8" (3.5 mm) diameter plug and impedance between 16 and 50 ohms. The recommended impedance is 32 ohms.

OPlugging in the headphones disconnects the speakers automatically. Adjust the volume using the VOLUME control.

Troubleshooting chart

Many potential problems can be resolved by the owner without calling a service technician. If something is wrong with this product, check the following before calling your authorized SHARP dealer or service center.

QGeneral

Symptom Possible cause

OThe clock is not set O Did a power failure occur?

to the correct time.	Reset the clock. (Refer page
	11)

OWhen a button is O Set the unit to the power

pressed, the unit	stand-by mode and then turn
does not respond.	it back on.

OIf the unit still malfunctions, reset it. (Refer page 14)

ONo sound is heard. O Is the volume level set to “0”? O Are the headphones

connected?

O Are the speaker wires disconnected?

QCD player

	Symptom	Possible cause
O	Playback does not	O Is the disc loaded upside
	start.	down?
O	Playback stops in	O Does the disc satisfy the
	the middle or is not	standards?
	performed properly.	O Is the disc distorted or
		scratched?
O	Playback sounds	O Is the unit located near
	are skipped, or	excessive vibrations?
	stopped in the	O Is the disc very dirty?
	middle of a track.	O Has condensation formed
		inside the unit?
O	“ER-CD21”	O Is the disc tray stopped with
	appears on the	force? Set the unit to the
	display.	power stand-by mode and
		then turn it back on.

QCassette deck

	Symptom		Possible cause
O	Sound skipping.	O	Is there any slack?
O	Cannot hear treble.	O	Is the tape stretched?

OSound fluctuation. O Are the capstans, pinch rollers, or heads dirty?

O Cannot remove the	O If a power failure occurs
tape.	during playback, the heads
	remain engaged with the
	tape. Do not open the
	compartment with great
	force.

E-13