IMPORTANT:

Be sure to first follow the

Quick Start Guide

on the reverse side to

complete initial setup of

your H700.

IMPORTANT:

Be sure to first follow the

Quick Start Guide

on the reverse side to

complete initial setup of

your H700.

H700

Bluetooth®

Handsfree Headset

TURNING ON AND OFF

To turn your headset on, open the
headset boom. The indicator light flashes
blue.
To turn your headset off, close the
headset boom. The indicator light will turn
off.
To conserve battery power, turn off your
headset when you don't plan to use it for
a while.

WEARING THE

HEADSET

Open the headset boom, then open the
earhook (45
°
from the headset).
Loop the earhook over your ear.
Press the headset to your ear.
Point the headset boom towards your
mouth.
1
2
3
4

CHANGING VOLUME

BUTTON ORIENTATION

You can also change the orientation of the
volume buttons on your headset.
Turn the headset power off.
Press the Call E button until the
indicator light becomes steadily lit in
purple, then press the Volume button
you want to assign as the "volume up"
button.
1
2

MAKING CALLS

Note: Your H700 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which
profile your phone supports. See your phone's user's guide
for more information.
Function  Action
Make a voice dial call Tap the Call button
and speak the 
name after the tone
End a call Tap the Call button
  
Receive a call Open headset boom 
or tap the Call button 
(if boom is already 
   open)
Reject a call Press and hold the
Call button until you
hear a beep
Redial last call Press and hold the
Call button until you
hear a beep
MAKING CALLS CONTINUED

Function  Action
Answer a second Press and hold the
incoming call Call button (places
first call on hold)
Toggle between two Press and hold
active calls the Call button
Join a 3-way call  Press and hold
both Volume buttons
Put an active call on Press and hold the
hold or resume a call Call button until you
on hold  hear a beep
Transfer a call from the Open headset boom
phone to the headset
Disable the Press and hold
indicator light both Volume
buttons for 3 to 4
   seconds
Mute or unmute a call Tap both Volume
   buttons
Note: Some features are phone/network dependent.

INDICATOR LIGHTS

With the Charger Plugged In
Indicator Light Headset Status
Red (steady) Charging (less the 
80% charged)
Yellow (steady) Charging (more than
80% charged)
Green (steady) Charging complete
With No Charger Plugged In
Indicator Light Headset Status
Off Power off
Purple (steady) Pairing mode/
Volume button 
orientation
Red Battery low
Blue (10 rapid flashes) Pairing successful
Blue (slow pulse)  Connected (on a call)
Blue (quick flash) Standby (not on call)
Note: After 5 minutes of inactivity, the light stops flashing to
conserve power, but the headset remains in standby mode.

AUDIO TONES

The audio tones provide information about your
headset status.
Audio Tone Headset Status
Single high tone when Volume at minimum
pressing Volume button or maximum
Five rapid high tones Low battery
repeated every 60 sec.
No audio indications; Out of range
deteriorating quality
Ring tone Incoming call
Single high tone Pairing confirmation
Single low tone Voice activation
Dual high/low tone Voice tag not
   recognized
Single high tone End call
Low to high tone Phone network 
not available
Two ascending tones Mute enabled
Two descending tones Mute disabled

CHANGING FOR USE

ON OTHER EAR

Open the headset boom,
then open the earhook
(90
°
from the headset).
Gently lift and pull the
top of the earhook up
and off the upper hinge
pin. Then, pull it away to
remove it.
Flip the headset over.
Hook the bottom of the
earhook onto the lower
hinge pin, then lift and
pull the top of the
earhook over the upper
hinge pin.
1
2
3
4
You can wear your H700 headset on your left or
right ear. The headset comes ready for the right
ear. To change the headset for the left ear:
1 Open Earhook
2 Pull Earhook Up
Hinge Pin
Multi-Color
Indicator Light
Volume
Buttons
Call
Button