Shure UR1M Replacement Parts And Accessories, Certification, Licensing Information, UA700, UA710

Overall Dimensions			UR1M Transmitter Audio Input:
49 mm L x 60 mm W x 17 mm D (1.9 x 2.38 x 0.66 in.)			Connector:	4-Pin male mini connector (TA4M)
Net Weight
				3-Pin female mini connector (LEMO XRB.00.303)
62 g (2.2 oz.) without batteries
			Input Configuration:	Unbalanced, active
Wiring
TA4F Connector			Maximum Input Level:	+5 dBu (sensitivity 0 dB)
Microphone Element	TA4F	TA4M	(1 kHz, 1% THD)	+15 dBu (sensitivity –10 dB)
	Connector	Connector
			TA4M Connector Pin	Pin 1: Ground
		UR1M MIC JACK BOARD
			Assignments:	Pin 2: +5 VDC bias
				Pin 3: Audio, 200 kΩ
				Pin 4: Tied through active load (on main board)
		Active Load		to ground.
				(On instrument adapter cable, Pin 4 floats)
		Audio
			LEMO Connector Pin	Pin 1: Ground
		Ground
			Assignments:	Pin 2: +5 VDC bias
NOTE: LAVALIER MIC TIES PINS 3 AND 4 TOGETHER—GUITAR CABLE DOES NOT.
				Pin 3: Audio
LEMO Connector				(8.2 kΩ between pin 2 and 3, internal to UR1M)

Microphone Element UR1M LEMO BOARD

Audio

Ground

Connector	Connector
UR1M Transmitter RF Output:
Connector:		SMA
Actual Impedance:		50 Ω
Pin Assignments:		Shell = Ground
		Center = Signal

REPLACEMENT PARTS AND ACCESSORIES

Furnished Accessories

Antenna, 470-530 MHz	UA700
Antenna, 518-578 MHz	UA710
Antenna, 578-698 MHz	UA720
Antenna, 740-865 MHz	UA730
Antenna, 944-952 MHz	UA740
Threaded Locking Adaptor (UR1M with TA4F)	WA340
Optional Accessories
Bodypack Pouch (Black)	WA581B
Bodypack Pouch (White)	WA581W
3-Pin mini Lemo conversion kit	WA335

Note

To fully interact with the Receiver, it is recommended to upgrade the UR4 firmware to 1.50 or higher and Shure Wireless Workbench to 5.0

Certification:

UR1M: Type Accepted under FCC Parts 74 (FCC ID: DD4UR1MA, DD4UR1MB, DD4UR1MC, DD4UR1MD, DD4UR1MF, DD4UR1MG, DD4UR1MRA,

DD4UR1MRB, DD4UR1MRC, DD4UR1MRG). Certified by IC in Canada under RSS-123 and RSS-102 (IC: 616A-UR1MA, 616A-UR1MB, 616A-UR1MC, 616A-UR1MD, 616A-UR1MRA, 616A-UR1MRB, 616A-UR1MRC).

The “EU Declaration of Conformity” can be obtained from Shure Inc. or any of its European representatives. For contact information please visit www.shure.com

LICENSING INFORMATION:

Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible requirements.

Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing of Shure wireless micro- phone equipment is the user’s responsibility, and licensability depends on the user’s classification and application, and on the selected frequency. Shure strongly urges the user to contact the appropriate telecommunications authority concerning proper licensing, and before choosing and ordering frequencies.

Information to User:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Operation of this device is subject to the following two conditions:

(1)this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired

operation of the device.

Note: EMC conformance testing is based on the use of supplied and recommended cable types. The use of other cable types may degrade EMC performance.

SHURE Incorporated http://www.shure.com United States, Canada, Latin America, Caribbean: 5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.

Phone: 847-600-2000 U.S. Fax: 847-600-1212 Int’l Fax: 847-600-6446 Europe, Middle East, Africa:

Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414 Asia, Pacific:

Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055

2