Sim2 Multimedia D35 Examples, Warnings, Select INPUT 3 COMP. RGB WITH YcrCb 15kHz SIGNAL

SIM2 D35

RS-232C CONTROL SPECIFICATIONS

	SET YCrCb AutoSync	BE EF 03 19 00 92 04 01 82 08 00 00 00 00 00 00
		14	00	00	00	00	00	00	00	00	00	00	00	00	00	00	00
	SET YCrCb 15kHz	BE EF 03 19 00 5B 0C 01 82 08 00 00 00 00 00 00
		08	00	00	00	00	00	00	00	00	00	00	00	00	00	00	00
INPUT 3	SET YCrCb 32kHz	BE EF 03 19 00 51 06 01 82 08 00 00 00 00 00 00
		10	00	00	00	00	00	00	00	00	00	00	00	00	00	00	00
(COMP. RGB) /
		BE EF 03 19 00 97 01 01 82 08 00 00 00 00 00 00
SIGNAL TYPE	SET RGB AutoSync
		18	00	00	00	00	00	00	00	00	00	00	00	00	00	00	00
	SET RGB 15kHz	BE EF 03 19 00 5E 09 01 82 08 00 00 00 00 00 00
		04	00	00	00	00	00	00	00	00	00	00	00	00	00	00	00
	SET RGB 32kHz	BE EF 03 19 00 98 0E 01 82 08 00 00 00 00 00 00
		0C	00	00	00	00	00	00	00	00	00	00	00	00	00	00	00

5. Examples

1.Send the simulated "SWITCH ON FROM STAND-BY AND SELECT SOURCE" Remote Control keycode.

Remote Control allows Switching on from Stand-by via one of the keys "1", "2" ... "5". Send, for instance, the code relative to key "1": BEEF02060080E5490100000000. The projector switches on and selects Input 1.

The projector returns the response code: 06 (Acknowledged with no error).

NOTE: Commands that simulate keys "1", "2" ... "5" switch on the unit and select the corresponding Source.

Command that simulate key 0 switches on the unit: the last source memorised prior to switch off is automatically selected.

2.Send the simulated "MENU RIGHT" Remote Control keycode. Send the packet: BEEF02060023E75A0100000000.

The OnScreen Display appers on the screen.

The projector returns the response code: 06 (Acknowledged with no error).

3.Send the "SET ASPECT ANAMORPHIC" Operation Code. Send the packet: BEEF0206009DF5840100000000.

The Aspect Ratio changes to Anamorphic.

The projector returns the response code: 06 (Acknowledged with no error).

4.Select "INPUT 3 (COMP. RGB) WITH YcrCb 15kHz SIGNAL"

Send the packet: BEEF0319005B0C01820800000000000008000000000000000000000000000000

Wait for the return code and add an additional delay of 40 ms.

Send the the code relative to the Key to which Input 3 has been assigned: for instance if the key is "3"

the code is: BEEF02060062E44B0100000000

6. Warnings

When the number of bytes sent to the Projector is greater than indicated for the Command (32 bytes for Operation Packets and 13 bytes for Event Packets), excess data will be ignored.

Conversely, if number of bytes sent to the Projector is smaller than required by the Communication Protocol, an Error Code will be returned.

Allow a time interval of at least 40 ms between the Return Code and the following Command.

9