Sioux Tools manual Model 5979A

		Model 5979A			Form # ZCE567A
		118" (3 rnm) Pencil Air Die Grinder
Operator Instructions			Important
Includes - Foreseen Use, Work Stations, Putting Into Service,			Read these instructions carefully before installing, operating,
			servicingor repairingthis tool. Keepthese instructions in a safe
Operating, Dismantling, Assembly and Safety Rules.			accessible place.
ManufacturerISupplier			ProductType		RPM
Sioux Tools, Inc.			118" (3 mm) Pencil		Cycles Per ~m
250 Snap-on Drive			Air Die Grinder
P.O. Box 1596						I
			Model No/Nos		Serial No.
Murphy, NC 28906
			1 5979A
U.S.A.
Tel No. 828-835-9765		Fax No. 828-835-9685
Product Net Weight		RecommendedUse Of	RecommendedHose Bore		Recommended Max.
0.44	Ibs	Balancer Or Support	Size - Minimum		Hose Length
0.20	Kg	NO	5/16 ins	8 mm	3 0 F t	1 0 M

Air Pressure					Noise Level: Sound Pressure Level 72.0 dB(A)
					Sound Power Level 84.0 dB(A)
RecommendedWorking	6.2	bar	90	PSI	Test Method: Tested in accordance with Pneurop
Maximum	6.2	bar	90	PSI

test code PN8NTC1 and IS0 Standard 3744

SAFETY MESSAGES

Personal Safety Equipment

Use - Safety lasses YES

Use - Safety Gloves YES Use- Safety Boots

Use - BreathingMasks YES

Use - Ear Protectors YES

A WARNING

Always Read Instructions

Before Using Power Tools

@Always Wear Safety

Goggles

@Wear Hearing Protection

Avoid Prolonged Exposure To Vibration

Vibration Level 2.0 Meters / Sec2

Test Method: Tested in accordance with IS0 standards 8662 Parts 1 & 13

Safety rules when using 5979A pencil Die Grinder

-Use accessories rated at least 70,000 RPM.

-Prolonged exposure to vibration may cause injury.

-Read all instructions before using this tool. All operators must be fully trained in its use and aware of these safety rules.

-Do not exceed the maximum working air pressure.

-Use personal protection equipment as recommended.

-Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicalsknownto cause cancer, birth defects and other reproductiveharm.

-Use only compressed air at the recommended conditions.

-If the tool appears to malfunction, remove from use immediately and arrange for service

and repair. If it is not practical to remove tool from service, then shut off the air supply to the tool and write or have written a warning note and attach it to the tool.

-If tool is to be used with a balancer or other suspension device, ensure that the tool is firmly attached to the

suspensionlsupport device.

-When operating the tool, always keep the body and particularly the hands away from the working attachment fixed to the tool.

-The tool is not electrically insulated. Never use the tool if there is any

chance of coming into contact with live electricity.

-Always when using the tool, adopt a firm footing and/or position and grip the tool sufficiently only to overcome

any reaction forces that may result from the tool doing work. Do not overgrip.

-Use only correct spare parts for maintenance and repair. Do not improvise or make temporary repairs. Major servicing and repairs should only be carried out by persons trained to do so.

-Do not lock, tape, wire, etc. the 'On/Off9valve in 'On' position. The triggerllever, etc. must always be free to

return to the 'Off'position when released.

-Always shut off the air supply to the tool and press the 'OnIOffvalve to exhaust the air from the feed hose before fitting, removing or adjusting the working attachment fitted to the tool.

-Before using the tool, make sure that a shut off device

Easy To Reach And	Air Tool
Operate Shut Off Valve

Page No 1