Skylink® Keyless Entry Transmitter | Model 18K |
|
|
1. INTRODUCTION |
|
|
|
|
|
5. KEYPAD OPERATION
In this package, you will find a keyless entry transmitter with 3V lithium batteries and screws.
1 pc 2.6 x 6 screw | Keyless Entry Transmitter | |
1 pc | 2.6 x 12 screw | (Batteries inside) |
1 pc | 2.6 x 25 screw |
|
2. PROGRAM A KEYPAD TO THE RECEIVER
You need to do the programming in order to add the keypad transmitter to the receiver.
1Plug the receiver 18R (sold separately) into an electrical socket.
2Press and hold the learn button at the left hand side of the receiver. The red LED on the receiver will flash.
3Press the
4The receiver red LED will go off indicates the programming is completed.
The backlight comes on and a beep is emitted when any key is pressed. The backlight of the keypad may not be visible when it is too bright outside. When any key is pressed, the next key must be pressed within 5 seconds or the backlight turns off and the sequence is cancelled. You must begin again.
If the keypad does not emit a beep when pressed, wait a few seconds and press the key again.
6. CHANGE PIN
Follow the instructions below to change the PIN.
To change your PIN:
1.Enter the current PIN, (factory default PIN 0 0 0 0), press * ,
2.Enter new 4 to 6 digit PIN, press * ,
3.Enter new PIN again, press * .
For example, if you are changing the PIN number from 0000 to
123456, enter the following sequence, 0000,* ,123456,* ,123456, * . If confirmed, the backlit LED flashes and the unit emits a long beep.
If you do not hear 3 beeps after the
|
| 7. BATTERY |
| - | Two 3 volt Lithium type (CR2032) |
| batteries (included). | |
|
| |
+ |
| It is time to change |
| the batteries when | |
|
| the backlight no |
|
| longer appears. |
|
| Battery Compartment |
5To program the keypad to control more than one receiver, repeat process (1) to (4) with different assigned door numbers.
6You can now mount the transmitter on a desired location.
Lift up the cover and insert screw above the keypad in the slot provided (a). Remove the battery cover and insert the second screw in the lower slot (b). Tighten all screws. Replace the battery cover, insert and tighten screw (c).
Learn Button
(a)
(c)
(b)
8. ADDITIONAL RECEIVER
You can use 18K to control up to 4 garage door openers by adding Skylink® Garage Door Receiver 18R for each opener.
9. FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
3.TROUBLE SHOOTING
Q:Door opener does not reac t after pressing the button on the transmitter.
A:- Ensure you hear 3 beeps from the keypad transmitter after entering the default PIN [0,0,0,0], [#], [1],. If you do not hear 3 beeps, that means the PIN you entered is incorrect.
-If the red light on the receiver flashes after entering the PIN on the transmitter, but the door opener does not respond, please ensure the red/black wire is successfully connected from the receiver to the wall mounted door control.
-Ensure the wires that are previously connected to the wall mounted door control are not loose.
-Ensure the keypad transmitter has been programmed to the receiver.
Refer to section 2 for how to program a keypad to the receiver.
4. REMOVE TRANSMITTER FROM THE RECEIVER
You can delete the transmitter from a receiver.
1Unplug the receiver from the electrical socket.
2Press and hold the learn button on the left hand side of the receiver when plugging the receiver into an electrical socket, the red LED on the receiver will flash rapidly. All the transmitters and keypads are deleted.
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
10. WARRANTY
If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization are required.
11. CUSTOMER SERVICE
If you would like to order Skylink’s products or have difficulty getting them to work, please :
1.visit our FAQ website at www.skylinkhome.com , or
2.email us at support@skylinkhome.com , or
3.call our toll free at
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Email:support@skylinkhome.com http://www.skylinkhome.com
P/N.
