4. CHANGE THE OPERATION CODE FOR BOTH TRANSMITTER AND RECEIVER (BOTH)
2 You can randomly remove some connectors, leaving some in place. A connector can be removed with the clip, as shown.
3If the connector is placed on the top and middle posts, that column is set on “ + ” . If the connector is placed on the middle and bottom posts, that column is set on “ - ”. If the connector is removed completely,
| (not placed on any posts), it is set to | |
| “ 0 ”. (see diagram for examples of | ‘0’ |
| how to set a column to the three |
| |
| different positions). When removing | ‘+’ |
| a connector to set a column to “ 0 ”, |
| save the connector in case you | ‘-’ |
| change the code at a later date. | |
4After setting up the code connectors on the keypad transmitter, you are ready to set the same code on the receiver.
Remove the receiver from the electrical outlet before
WARNING changing the code.
5 Remove the screw that holds the connector cover, and remove the cover.
6You will see 10 connectors. The settings must match with those of the transmitter.
Connectors 1 to 10 are the same.
7Put the cover and screw back onto the receiver. Plug the receiver into an electrical outlet.
8Enter [0,0,0,0] [#] will open the garage door.
9You can now mount the transmitter on a
desired location. | (a) |
Lift up the cover and insert screw | |
above the keypad in the slot provided (a). | |
Remove the battery cover and insert | |
the second screw in the lower slot (b). | |
Tighten all screws. Replace the battery | (c) |
cover, insert and tighten screw (c). | (b) |
|
5. KEYPAD OPERATION
NOTE:
The backlight comes on and a beep is emitted when any key is pressed. The backlight of the keypad may not be visible when it is too bright outside. When any key is pressed, the next key must be pressed w ithin 5 seconds or the backlight turns off and the sequence is cancelled. You must begin again.
If the keypad does not emit a beep when pressed, wait a few seconds and press the key again.
6. CHANGE PIN
Follow the instructions below to change the PIN.
To change your PIN:
1.Enter the current PIN, (factory default PIN 0 0 0 0), press * ,
2.Enter new 4 digit PIN, press * ,
3.Enter new PIN again, press * .
For example, if you are changing the PIN number from 0000 to 1234, enter the following sequence, 0000,* ,1234,* ,1234, * .
If confirmed, the backlit LED flashes and the unit emits a long beep.
If you do not hear 3 beeps after the 4-digit PIN and [#] is entered,
that means you have entered an incorrect PIN, and the keypad transmitter will not operate your garage door.
7. BATTERY
Two 3 volt Lithium type (CR2032) batteries (included).
| - | It is time to change |
| the batteries when |
| | the backlight no |
| + | longer appears. |
| Battery Compartment |
| |
8. ADDITIONAL TRANSMITTER
You can add as many additional transmitters as you want to control the same receiver. Simply set the same operation code on all transmitters with the same code setting on the receiver. Skylink® offers Keychain Transmitter Model 318TN and Keyless Entry Transmitter Model 318K to work with your receiver. For more information, please visit our website at www.skylinkhome.com or contact us.
9. CAUTION
RISK OF ELECTRICAL SHOCK. FOR INDOOR USE ONLY. CAUTION : DISCONNECT POWER BEFORE CODE CHANGING. REPLACE COVER AFTER CODE CHANGING.
Maximum Rating:
Input : 120VAC 60Hz 2W
10. FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
11. WARRANTY
If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization are required.
12. CUSTOMER SERVICE
If you would like to order Skylink’s products or have difficulty getting them to work, please :
1.visit our FAQ website at www.skylinkhome.com , or
2.email us at support@skylinkhome.com , or
3.call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST. Fax +800 286-1320
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Email:support@skylinkhome.com http://www.skylinkhome.com
P/N. 101A207-004 Rev.4 ©2005 SKYLINK GROUP
