Smart ButtonTM |
|
Garage Door Receiver | Model |
|
|
1. INTRODUCTION |
|
|
|
Congratulations on your purchase of the Skylink® Smart ButtonTM. The Smart ButtonTM is designed to work with Skylink® remote control G6M, G6K, G6V, G6T3 , SkylinkhomeTM system remote, and more to operate the Garage Door Opener. In this kit, you will find the following:
|
|
| Mounting Screws |
|
|
|
|
| and anchors |
|
|
| Smart Button | TM | Crimper | ||
|
|
|
| ||
|
| Double Sided Tape |
|
| |
|
|
|
|
| |
|
|
|
|
| |
|
| 2. INSTALLATION |
|
| |
|
|
|
|
|
|
| Unplug the power cord of your garage door opener | ||||
WARNING | before installation to ensure power is not connected. | ||||
|
|
|
|
| |
|
|
|
| Easy ClipTM |
1. Open up the “Easy ClipTM” and place it underneath the existing 2 wires of the wall button / wall console.
2. Ensure a pair of the wall button ribbon wires are placed properly inside the channels of the “Easy ClipTM”.
Wall Button
Ribbon Wires
NOTE:
Ensure the ribbon wires are not twisted but laid flat inside the clip.
Press / lock
2.INSTALLATION (CONT)
5.If the wall button wires are hidden inside the
wall, please connect the “Easy ClipTM” to the exposed wires attached to the terminals of the garage door
opener.
6.Power up the garage door opener, the red LED on the Smart ButtonTM
If the Smart ButtonTM
for 2 minutes, your garage door opener is probably too old. However, the Smart ButtonTM will still work if you plug in an adapter (purchased separately). Please contact Skylink® to purchase the adapter.
Rating of the transformer:
12V DC, 100mA Diameter of DC plug : 3.5mm
7. Secure the SmartButtonTM
Note: Do not cut the antenna! Straighten up the antenna to improve signal reception.
Note:
After installation of the “Easy Clip TM ”, if you want to
3. OPERATION
If the red LED flashes slowly, the Smart ButtonTM
| LED |
Press the programmed button on the remote control |
|
or Smart ButtonTM | OPEN / |
If your wall button ribbon wires
are not the same kind as shown in the diagram, please visit our
website www.skylinkhome.com or contact us for more information.
Ribbon Wires
garage door. | CLOSE |
| Button |
Programming
Learn additional remote controls
3.Press and lock the clip by snapping it together. The included Crimper helps you lock the “Easy ClipTM”. Close the cover and press down to lock the cover using this Crimper until you hear a “click”.
Smart ButtonTM
1. Press the learn button on the side of the
2. Once the learn button is pressed, the LED will
flash quickly. Release the learn button.
LED
3. Within 30 seconds, press the button on the remote control you would like to program.
4.Once the remote control is programmed, the LED will flash slowly, in the same way as it flashes in standby mode.
4.If the “Easy ClipTM” cannot clip with the wires from your wall button, cut off the “Easy ClipTM” then connect two wires from the Smart ButtonTM to the wall button.
5. You may now operate the garage door opener with this remote control.
Erase remote controls
Learn Button
a) Dismount the existing wall button from the wall.
b) Connect the 2 wires from the Smart ButtonTM
c) Mount the wall button back.
To erase unwanted remote control(s)from the memory of Smart ButtonTM
To erase remote control(s), follow the steps below:
1.Press and hold the learn button for approximate 10 seconds.
2.The LED will flash rapidly after 10 seconds to indicate all the pro- grammed remote controls have been erased. Release the learn button.
3.You have erased all the remote controls programmed to the Smart ButtonTM