Deluxe Home Monitoring Kit | Model |
|
|
1.INTRODUCTION |
|
|
|
The Deluxe Home Monitoring Kit is designed to monitor movement or any door and window around your house. The motion sensor can be placed either indoor or outdoor. Once motion is detected or a window/door is opened, the receiver will ash along with alert beeping or alarm.
In this package, you should nd two Window/Door Sensors, a Motion Sensor, a Household Alert® Long Range Receiver, an adapter,
2 pcs 3x18screws
| Indoor/Outdoor |
| |
| Motion Sensor |
| |
Adapter |
| Household Alert® | |
| Mounting | ||
| Long Range Receiver | ||
2 x Magnet Sensor | Accessories | ||
| |||
|
|
Please follow the instructions below to setup your motion sensor and the receiver.
2. PROGRAMMING MOTION SENSOR
The sensor must be programmed to the Household Alert® Long Range Receiver before they can communication. You may program the sensors to one of the 4 zones. Follow the instructions below:
1.Plug in an AC adapter to the receiver.
2.The green LED will be on indicating it is turned on.
3.Open the back cover and there is a learn button. Press and hold this learn button for 5 seconds, until both green LED and zone 1 red LED 
You may now release the learn button.
4.If you would like to program the sensor to zone 1, activate the
sensor while the zone 1 red LED is 
Press the SET button on the back of the sensor to activate it.
5.If you would like to program the sensor to other zones, press the
learn button again, until the red LED 
at the zone you want to program the sensor to, then activate the sensor.
6.Once the sensor is programmed, the green LED will be steadily on and none of the red zone LEDs will be on.
SET Button
Plug in the adapter to the receiver
|
| Insert 9V alkaline battery (option) to the sensor | |
Learn Button | |||
| |||
Note: Each zone can program up to 4 sensors. If you try to program a
sensor into a zone, the 
programmed sensor will be erased.
Erasing a sensor
You cannot erase a 
sensor. You must erase all sensors from the receiver, then program the ones you would like to keep. To erase all the sensors from the receiver:
1.Remove the adapter from the receiver.
2.Open the back cover, press and hold the learn button. Do not release the learn button until step 4.
3.While holding onto the learn button, plug in the adapter to the receiver.
4. You may release the learn button when the LEDs on the receiver are on. 5. You have erased all sensors from the receiver.
Page 1 of 3
3. MOTION SENSOR INSTALLATION
MOUNTING
A
WALK TEST |
|
After mounting the sensor at the desired location, it is | 7 ft |
important to perform a walk test in order to determine | |
if the sensor is detecting the things you want to detect. |
|
In order to control how far the sensor can “see”, this can be done by adjusting the angle of the sensor. To reduce the detection range, simply move the sensor downward. To increase the range, move the sensor up to around 12 degrees. This will give the maximum range. However,
this may not be desired if the sensor is placed outdoors, since | a false |
trigger may occur if the sensor is set to detect motion in a distance.
You should walk in the area that you would like the sensor to monitor. Place the slide switch on the side of the receiver to “Alert” position. The receiver will beep if the sensor detects your movement. If the receiver does not respond, adjust the mounting angle accordingly. After motion is detected once, the sensor will not be triggered unless no motion is detected for 20 seconds. Therefore, wait for at least 20 seconds during walk testing between 2 activations.
Perform walk test in the undesired area to ensure movement cannot be detected.
Tips: The sensor should not face towards direct sunlight, placing nearheat or cold producing | devices (i.e. A/C or furnance vents, fans, ovens, | ||||||||||
| heaters etc.) that may | cause false triggers. | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Move the sensor downward to | Move the sensor up to around |
reduce the range. | 12ºtogivemaximumrange. |
SENSOR SENSITIVITY
The sensitivity of the motion sensor is adjustable. Change the setting by placing the connector on either the ”High” (connector position “1”) or “Low” (connector position “2”) position. When the sensitivity is set to “Low”, more movement is required to trigger the sensor. It is recom- mended to set the sensitivity to “Low” and perform a “Walk Test”. If the
walk test result is | the sensitivity does not require to be | |
adjusted further. If the walk test |
| |
result shows the sensitivity is too |
| |
low, then you can change the |
| |
sensitivity setting to “High”. Please |
| |
perform the walk test after changing |
| |
the sensitivity setting. |
|
|
| 1 - High | 2 - Low |
