7. TRANSMITTER PASSWORD PROTECTION
Password protection
The
Password can be
Note:
[1] = Button 1 [2] = Button 2 [3] = Button 3
8. OPTIONAL ACCESSORIES AND OPERATIONS
You can add up to sixteen single button transmitters or keypads or five
Program additional remote controls
Smart ButtonTM
To learn additional remote controls, follow the instructions below:
Button [1]
Button [2]
Button [3]
Note:
The
The factory default password is 2, 2, 2, and this password function is disabled out of factory.
1.Press the learn button on the side of the
2.Once the learn button is pressed, the LED will flash quickly. Release the learn button.
3.Within 30 seconds, press the button on the remote control you would like to program.
4.Once the remote control is programmed, the LED will flash slowly, in the same way as it flashes in standby mode.
5.You may now operate the garage door opener with this remote control.
LED
Learn Button
Change password
1.Press 1 and 3 simultaneously and hold for more than 6 seconds until the LED changes from flashing quickly to flashing slowly.
2.Input old password.
3.Press 1 and 3 once simultaneously to confirm. If the password is wrong, the LED will flash 3 times and you have to start it over from step1.
4.Input new password.
5.Press 1 and 3 once simultaneously to confirm.
6.Input new password again.
7.Press 1 and 3 once simultaneously to
Disable password
1.Press 1 and 3 simultaneously and hold for more than 2 seconds until the LED flashes quickly but not until the LED flashes slowly.
2.Input old password.
3.Press 1 and 3 once simultaneously to confirm. If the password is correct, the password protection will be disabled.
Enable password
1.Press 1 and 3 simultaneously and hold for more than 2 seconds until the LED flashes quickly but not until the LED flashes slowly.
2.Input old password.
3.Press 1 and 3 once simultaneously to confirm. If the password is correct, the password protection will be enabled.
You can toggle the two states - password protection enabled or disabled.
Note:
The
If you forget your password and want to reset
1.Press 1 and 2 simultaneously and hold for more than 10 seconds until the LED flashes.
2.After you release 1 and 2, the LED will be turned off and
After the reset, password protection is removed but the remote can not control any receiver until you reprogram it to receivers you want to control.
For more information, please visit our website at www.skylinkhome.com or contact us.
9. BATTERY
3 Volt lithium battery (CR 2032) (included).
It is time to change the battery when the red LED on the transmitter does not turn on when either button is pressed.
10. WARNING
DO NOT let children use the garage door transmitter without adult supervision. Otherwise, Children and others may be injured by the garage door.
11. FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
12. WARRANTY
If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization are required.
13. CUSTOMER SERVICE
If you would like to
-find out the
-know more about features and applications
-download documents, i.e. user’s instructions
-order Skylink products
or if you have difficulty getting products to work, please:
1.visit our FAQ section at www.skylinkhome.com, or
2.email us at support@skylinkhome.com, or
3.call our toll free at
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Email:support@skylinkhome.com http://www.skylinkhome.com
P/N :
Patent Pending
®are registered trademarks of their respective corporations ©2010 SKYLINK GROUP