SLANT/FIN CORPORATION, Greenvale, N.Y. 11548 • Phone: (516) 484-2600
FAX: (516) 484-5921•
Canada: Slant/Fin
LTD/LTEE
, Mississauga, Ontario
www.slantfin.com
®
©Slant/Fin Corp. 1996.
LIGHTING INSTRUCTIONS (Reference For Labels 65-0640 and 65-0645)CONCEPT 214
FOR YOUR SAFETY READ BEFORE OPERATING
WARNING:If you do not follow these instructions
exactly,a fire or explosion may result causing property
damage,personal injury or loss of life .
A. This appliance does not have a pilot. It is equipped with an
ignition device that automatically lights the burner. DO NOT
try to light the burner by hand.
B. BEFORE OPERATING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
WHATTO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
• DO NOT touch any electric switch; DO NOTuse any phone in
your building.
• Immediately call your gas supplier from a neighbor's phone.
Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to turn the gas control knob or depress
and move the gas control selector arm. NEVER use tools. If
the knob will not turn or selector arm will not depress or
move by hand, DON'T try to repair it, call a qualified service
technician. Force or attempted repair may result in a fire or
explosion.
D. DO NOTuse this appliance if any part has been underwater.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been underwater.
OPERATING INSTRUCTIONS (Label 65-0640)
•STOP!Read the safety information above on this label.
• Set the room thermostat to lowest setting.
• Turn off all electric power to the appliance.
• This appliance is equipped with an ignition device which
automatically lights the burner. DO NOTtry to light the
burner by hand.
• Remove control access panel.
• Turn gas control knob clockwise to “OFF” position.
• Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP!Follow
"B" in the safety information above on this label. If you don't
smell gas, go to the next step.
• Turn gas control knob counterclockwise to “ON”
position.
• Replace control access panel.
• Turn on all electric power to the appliance.
• Set room thermostat to desired setting.
• If the appliance will not operate, follow the instructions “To
Turn Off Gas To Appliance” and call your service technician
or gas supplier.
TO TURN OFF GAS TO APPLIANCE
• Set room thermostat to lowest setting.
• Turn off all electric power to the appliance if service is to be
performed.
• Remove control access panel.
• Turn gas control knob clockwise to “OFF” position.
• Replace control access panel.
OPERATING INSTRUCTIONS (Label 65-0645)
•STOP!Read the safety information above on this label.
• Set the room thermostat to lowest setting.
• Turn off all electric power to the appliance.
• This appliance is equipped with an ignition device which
automatically lights the burner. DO NOTtry to light the
burner by hand.
• Remove control access panel.
• Depress and move gas control selector arm left to
“OFF” position. Note: Arm cannot be turned to “OFF” unless
arm is pushed in slightly. DO NOTforce.
• Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP!Follow
"B" in the safety information above on this label. If you don't
smell gas, go to the next step.
• Depress and move gas control selector arm right to
“ON” position.
• Replace control access panel.
• Turn on all electric power to the appliance.
• Set room thermostat to desired setting.
• If the appliance will not operate, follow the instructions “To
Turn Off Gas To Appliance” and call your service technician
or gas supplier.
TO TURN OFF GAS TO APPLIANCE
• Set room thermostat to lowest setting.
• Turn off all electric power to the appliance if service is to be
performed.
• Remove control access panel.
• Depress and move gas control selector arm left to
“OFF” position.
• Replace control access panel.
ON
OFF