Snapper 3500W Portable Generator

OPERATING THE

GENERATOR

Starting the Engine

Disconnect all electrical loads from the generator. Use the following start instructions:

1.Make sure unit is on a level surface.

IMPORTANT: Failure to start and operate unit on a level surface will cause the unit not to start or shut down during operation.

2.Turn the fuel valve to the “On” position (Figure 4).The fuel valve handle should be vertical (pointing toward the ground) for fuel to flow.

Figure 4 — Fuel Valve

Fuel Valve is shown in the On position

3.Start engine according to instructions given in the engine operator’s manual.

WARNING

Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

•When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback.

•NEVER start or stop engine with electrical devices plugged in and turned on.

NOTE: If engine starts after 3 pulls but fails to run, or if unit shuts down during operation, make sure unit is on a level surface and check for proper oil level in crankcase.

This unit may be equipped with a low oil protection device. See engine operator’s manual.

WARNING

Running engines produce heat.Temperature of muffler and nearby areas can reach or exceed 150°F (65°C).

Severe burns can occur on contact.

Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire.

•DO NOT touch hot surfaces and avoid hot exhaust gases.

•Allow equipment to cool before touching.

•Keep at least 5 ft. (152 cm) clearance on all sides of generator including overhead.

•Code of Federal Regulation (CFR) Title 36 Parks, Forests, and Public Property require equipment powered by an internal combustion engine to have a spark arrester, maintained in effective working order, complying to USDA Forest service standard 5100-1C or later revision. In the State of California a spark arrester is required under section 4442 of the California Public resources code. Other states may have similar laws.

Connecting Electrical Loads

•Let engine stabilize and warm up for a few minutes after starting.

•Plug in and turn on the desired 120 and/or 240 Volt AC, single phase, 60 Hz electrical loads.

•DO NOT connect 240 Volt loads to the 120 Volt duplex receptacles.

•DO NOT connect 3–phase loads to the generator.

•DO NOT connect 50 Hz loads to the generator.

•DO NOT OVERLOAD THE GENERATOR. See “Don’t Overload Generator”.

CAUTION

Exceeding generators wattage/amperage capacity can damage generator and/or electrical devices connected to it.

•See “Don’t Overload Generator”.

•Start generator and let engine stabilize before connecting electrical loads.

•Connect electrical loads in OFF position, then turn ON for operation.

•Turn electrical loads OFF and disconnect from generator before stopping generator.

9

Page 8 Page 10
Page 9
Image 9
Snapper 030214 manual Operating Generator, Starting the Engine, Connecting Electrical Loads
Page 8 Page 10

030214 specifications

Snapper 030214 is a cutting-edge model in the world of personal transportation, designed to cater to the needs of modern commuters and recreational enthusiasts. This compact electric vehicle combines innovative technologies with top-notch features to create a versatile and eco-friendly mode of transport.

One of the standout characteristics of the Snapper 030214 is its lightweight frame, crafted from durable materials that enhance both portability and resilience. Weighing in at just 25 pounds, it is easily transportable, making it an ideal choice for individuals who prefer a quick, hassle-free commuting solution. Its foldable design allows users to store it conveniently in small spaces, such as under a desk or in the trunk of a car.

Powering the Snapper 030214 is a high-efficiency electric motor that delivers impressive performance while minimizing environmental impact. The vehicle boasts a top speed of 15 miles per hour, making it suitable for urban environments where quick maneuverability is essential. In addition, its advanced battery technology provides an impressive range of up to 30 miles on a single charge, ensuring that users can complete their journeys without the anxiety of running out of power.

The snapper is equipped with cutting-edge regenerative braking technology, which not only enhances the overall efficiency of the vehicle but also extends battery life. This innovative feature captures the energy generated during braking and redirects it to recharge the battery, allowing for longer rides without the need for frequent charging.

Comfort and safety are also paramount in the design of the Snapper 030214. The model features an ergonomic seat and adjustable handlebars, ensuring a comfortable ride for users of various heights. Additionally, the inclusion of bright LED headlights and taillights enhances visibility in low-light conditions, contributing to overall safety.

Moreover, the Snapper 030214 includes a user-friendly digital display that provides essential information such as speed, battery level, and distance traveled. This allows riders to stay informed during their trip, making their experience more enjoyable.

In summary, the Snapper 030214 exemplifies a perfect blend of functionality, eco-friendliness, and user-centric design. With its lightweight frame, powerful electric motor, and innovative features, it stands out as an ideal choice for anyone looking to enhance their personal mobility while contributing positively to the environment.
Top Page Image Contents