Manuals / Snapper / Lawn and Garden / Lawn Mower

Snapper CP215019KW, CP215519HV important safety instructions Propelled Models

Models: CP215019KW, CP215519HV CP216019KWV, CP215519HV

1 32

Download 32 pages 47.45 Kb

Page 1

Safety Instructions & Operator’s Manual for

Safety Instructions & Operator’s Manual for

21” STEEL DECK

WALK MOWERS COMMERCIAL MODELS SERIES 19

PROPELLED

MODELS

CP216019KWV

CP215519HV

MODEL NUMBER EXPLANATION

C

P

21

60

19

KW

V

MODEL DESIGNATION

SELF-PROPELLED

CUTTING WIDTH

C – Commercial Model	55 – 5.5 HP (Engine Horse Power)
P – Self Propelled Model	60 – 6.0 HP (Engine Horse Power)
21 – 21” Cutting Width

ENGINE DESIGNATION

SERIES DESIGNATION

ENGINE HORSE POWER *

19 - Series Designation	KW – Kawasaki Engine
H – Honda Engine	V – Overhead Valve

Thank you for buying a SNAPPER Product! Before operating your Walk Behind, read this manual carefully and pay particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 - 4. Remember that all power equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in accordance with the operating instructions and common sense.

NOTE: Specifications are correct at time of printing and are subject to change without notice.

* Actual sustained equipment horsepower will likely be lower due to operating limitations and environmental factors.

COPYRIGHT © 2005

SNAPPER – A DIVISION OF SIMPLICITY MFG., INC.

ALL RIGHTS RESERVED

MANUAL No. 7100373 (I.R. 10/4/2005) TP 100-5092-IR-WB-N

Image 1

Snapper CP215019KW, CP215519HV important safety instructions 21” STEEL DECK WALK MOWERS COMMERCIAL MODELS SERIES

Contents

21” STEEL DECK WALK MOWERS COMMERCIAL MODELS SERIES Safety Instructions & Operator’s Manual forPROPELLED MODELS CP216019KWV CP215519HVPROTECTION FOR CHILDREN IMPORTANT SAFETY INSTRUCTIONSSLOPE OPERATION PREPARATIONMAINTENANCE AND STORAGE IMPORTANT SAFETY INSTRUCTIONSSAFE HANDLING OF GASOLINE OPERATIONMAINTENANCE AND STORAGE IMPORTANT SAFETY INSTRUCTIONSTABLE OF CONTENTS ENGINE SPEED CONTROL Section 1 - FAMILIARIZATION1.1 INTRODUCTION 1.2 NOMENCLATURE2.1 PRE-START CHECK LIST Section 2 - OPERATING INSTRUCTIONS2.2 STARTING & OPERATION 2.2.1. ENGINE & BLADE FIGURE 2.3a2.5 CUTTING HEIGHT ADJUSTMENT 2.4 HANDLE HEIGHT ADJUSTMENTSection 2 - OPERATING INSTRUCTIONS 2.2.3. PROPELLING MOWER2.7 INSTALLATION of RECYCLING PLUG Optional Accessory on Some Models 2.6 INSTALLATION of GRASS BAG ADAPTERSection 2 - OPERATING INSTRUCTIONS Section 2 - OPERATING INSTRUCTIONS 1. Grasp bag connector and bag handle as shown. See Figure1. Set all wheels in the highest cutting position Notch Section 2 - OPERATING INSTRUCTIONSSection 3 - MAINTENANCE IMPORTANT Drain fuel tank before tipping mower Section 3 - MAINTENANCESection 4 - REPAIR & ADJUSTMENTS 4. Sharpen blade on a grinding wheel at an angle of Section 4 - REPAIR & ADJUSTMENTS1. Grease on drive disc causing slippage Section 4 - REPAIR & ADJUSTMENTS7. Reinstall driven disc spring to driven disc assembly Section 4 - REPAIR & ADJUSTMENTSBEARING Section 4 - REPAIR & ADJUSTMENTSREMOVE FOUR MACHINETo replace the bearing on the pulley end of the hex Section 4 - REPAIR & ADJUSTMENTSRemove the driven disc. Refer to Section Section 4 - REPAIR & ADJUSTMENTSPROBLEM TROUBLESHOOTINGPROBABLE CAUSE CORRECTIVE ACTIONMAINTENANCE PARTS SERVICE SCHEDULE2 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE SNAPPER PRODUCT REGISTRATION FORM Page Page Page Safety Instructions & Operator’s Manual for 21” STEEL DECK WALK BEHIND MOWERS COMMERCIAL MODELS SERIES