TROUBLESHOOTING
PROBLEM |
|
| PROBABLE CAUSE |
| CORRECTIVE ACTION |
|
|
|
|
|
|
| |
Engine Will Not Start | 1. | Fuel tank empty or fuel valve OFF. | 1. | Fill fuel tank with fresh fuel. Turn valve ON. |
| |
Using Recoil Starter |
|
|
|
|
| |
2. | Engine needs choking. | 2. | Move choke control to “CHOKE” position. |
| ||
|
|
|
|
| ||
| 3. | Spark plug wire disconnected. | 3. | Place spark plug wire onto spark plug. | ||
|
|
|
|
| ||
| 4. | Engine speed control in STOP position. | 4. | Move control to choke or fast position. |
| |
|
|
|
| |||
Engine Stalls or Stops | 1. Choke control in the “CHOKE” position. | 1. Move choke control to “OFF” position. |
| |||
After Running |
|
|
|
|
|
|
| 2. Fuel tank empty. | 2. Fill with fuel to proper level. |
| |||
| 3. Engine air | 3. Clean free of all debris. |
| |||
| 4. Spark plug defective or gap set improperly. | 4. Service spark plug. |
| |||
| 5. Water, debris or stale fuel in fuel system. | 5. Drain and clean fuel system. |
| |||
Engine Loses Power | 1. | Engine air | 1. | Clean or replace filters. |
| |
|
|
|
|
|
| |
| 2. | Spark plug faulty. | 2. | Service spark plug. |
| |
| 3. | Water, debris or stale fuel in fuel system. | 3. | Drain and clean fuel system. |
| |
|
|
|
|
|
| |
Excessive Vibration | 1. | Damaged, out of balance or bent mower blades. | 1. | Service mower blade(s). |
| |
|
|
|
|
|
| |
| 2. | Loose blade components. | 2. | Service and tighten loose parts. |
| |
|
|
|
|
|
| |
| 3. | Loose or missing air lift (if equipped). | 3. | Replace air lifts. Tighten to proper torque. |
| |
|
|
|
|
|
| |
| 4. | Lumpy or frayed belt. | 4. | Replace belt. |
| |
|
|
|
|
|
| |
| 5. | Bent Idler pulley. | 5. | Replace pulley. |
| |
|
|
|
|
| ||
Mower Will Not Move | 1. Damaged transmission. | 1. | Contact authorized SNAPPER dealer. |
| ||
Loss Of Traction | 2. Traction drive belt requires replacement. | 2. | Replace traction drive belt. |
| ||
3. Driven disc slipping. | 3. | Clean or replace driven disc. |
| |||
|
|
|
|
| ||
Cutting Grass | 1. Cutting height too low or high. | 1. | Adjust cutting height. |
| ||
|
|
|
| |||
Improperly | 2. Engine speed too slow. | 2. Move engine speed control to “FAST” position. |
| |||
|
|
|
|
|
| |
| 3. | Forward ground speed too fast. | 3. | Move ground speed control to a slower speed. |
| |
|
|
|
|
|
| |
| 4. | Terraced cut, side to side. | 4. | Adjust height of cut with height adjust levers. |
| |
|
|
|
|
|
| |
| 5. | Excessive deck pitch, front to rear. | 5. | Adjust height of cut with height adjust levers. |
| |
|
|
|
|
|
| |
| 6. | Cutting blade(s) dull or damaged. | 6. | Sharpen cutting edges or replace blade(s). |
| |
|
|
|
|
| ||
Poor Grass Discharge | 1. Engine speed too slow. | 1. | Move engine speed control to “FAST” position | . | ||
|
|
|
|
|
| |
| 2. | Forward speed too fast. | 2. | Move ground speed control to a slower speed. |
| |
|
|
|
|
|
| |
| 3. | Grass is wet. | 3. | Mow when grass is dry. |
| |
|
|
|
|
|
| |
| 4. | Excessively worn or damaged blade(s). | 4. | Service mower blade(s). |
| |
|
|
|
|
|
| |
| 5. | Build up of grass clippings and debris under deck. | 5. | Clean deck. |
| |
|
|
|
|
|
| |
| 6. | Improper blade(s) installed on deck. | 6. | Install proper SNAPPER blades. |
| |
|
|
|
|
|
| |
| 7. | Blade(s) installed improperly on deck. | 7. | Install blades properly. |
| |
|
|
|
|
| ||
Oil Leaking | 1. Leaking engine case. | 1. | Contact authorized SNAPPER dealer. |
| ||
|
|
|
| 2. | Check and tighten drain plug. |
|
|
|
|
| 3. | Make sure dip stick or oil filler cap is securely |
|
|
|
|
|
| in place. |
|
19
