Figure 5
Figure 7
Blade Control (2)
Drive
Control (2)
Oil Fill and
Dipstick

Quick Setup Guide

Self-Propelled Mower

Models

SPXV2270HW

NSPXV2270HW

Questions?

Do not return to the store. We can help.

Call Customer Service Toll-Free 1-800-317-7833Or visit our website www.snapper.com

Overview

Starter Rope

Handle

Fuel Fill Cap

Mulching

Cover

Cutting Height

Adjust Lever

3-in-1: Convert from mulching to bagging to side-discharge:

1 Unpack the mower

 

 

 

 

 

 

4 Add oil and fuel

• Cut all four corners of the box from top to bottom.

 

 

 

 

• Move the mower outside to a flat, level surface.

• Remove all packing materials from the mower.

 

 

 

 

Remove the oil fill cap (A, Figure 3). Add the entire contents of the

 

 

A

 

 

supplied oil container to the engine. Replace the oil fill cap.

 

 

 

 

 

 

 

 

• Locate and identify the items included with the mower.

 

 

 

 

A

IMPORTANT Mower is shipped without oil in engine.

 

 

 

 

 

 

 

 

 

Failure to add oil before starting engine will result in

 

 

 

 

 

 

 

 

 

engine damage.

 

 

 

 

 

 

B

 

Remove the fuel fill cap (B). Following the three-step instructions on

 

 

 

 

 

 

 

 

2 Raise the handle assembly

 

 

 

 

B

the FreshStart® card, snap the fuel preserver cartridge into the bottom

 

 

 

 

of the fuel fill cap.

 

 

 

 

• Add clean, fresh, UNLEADED fuel with a minimum of 87 octane,

• Loosen, but do not remove, the knobs (A, Figure 1)

 

 

 

 

 

 

 

 

 

leavi g one inch of space from the top of the tank for fuel expansion.

 

on both sides of the upper handle.

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE: Fuel blends containing more than 10% ethanol are not

 

 

 

 

 

 

 

 

 

Unfold the upper handle so that it is aligned with the

 

 

 

 

 

recommended.

 

 

 

 

 

IMPORTANT Fuel tank holds less than 1/2 gallon.

 

lower handle, and tighten the upper knobs.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IMPORTANT DO NOT mix oil with fuel.

• Remove the handle knobs, washers and carriage bolts

 

 

 

 

 

IMPORTANT DO NOT use E85 fuel.

 

 

 

 

 

 

 

from the lower handle (B).

 

 

 

 

 

 

Replace the fuel fill cap, and wipe up any spills.

 

 

 

 

Figure 1

 

 

 

 

 

 

 

 

 

 

Raise the lower handle, aligning it with one of the

 

for

 

 

 

 

three sets of holes in the handle bracket. (Most users

 

 

5 Final preparation

 

will prefer the middle position). Replace the hardware,

 

 

 

tightening securely.

 

 

 

 

 

 

 

 

 

 

 

 

Move the cutting height adjust levers (A, Figure 4) to the desired

 

 

 

 

 

 

 

 

 

cutting height.

 

 

 

 

 

 

 

 

Set the mower to mulch, bag, or discharge. (See 3-in-1 instructions

3 Set Up the starter rope handle

 

 

B

 

 

below.)

 

C

 

 

B

 

Squeeze the blade control (A, Figure 2) against the

 

 

A

 

 

 

 

 

 

 

 

 

 

Not

 

 

 

6 Read the manuals

 

drive control (B). NOTE: The blade control and drive

 

D

 

 

 

control can be operated from either side.

 

 

 

 

 

 

 

A

Pull the starter rope handle (C) out of the ngine to

 

 

 

• Carefully read all the manuals supplied with the mower.

 

 

 

 

 

 

 

 

 

They contain important safety, operating, and maintenance

 

the rope guide (D). Hook the starter rope into the

 

 

 

 

 

 

 

 

 

 

 

information.

 

rope guide (it might be a tight fit).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 2

 

 

 

 

 

 

Reproduction

BA

Figure 3

DANGER

Fuel stabilizer is a hazardous chemical.

IF SWALLOWED, call a physician immediately. Fuel stabilizer contains:

2,6-di-tert-butylphenol (128-39-2) and aliphatic petroleum distillate (64742-47-8).

Running engines give off carbon monoxide, an odorless, colorless, poison gas. Breathing carbon monoxide can cause nausea, fainting, or death.

Operate this product ONLY outdoors.

Keep exhaust gas from entering a confined area through windows, doors, ventilation intakes or other openings. DO NOT operate this product inside any building or enclosure, even if windows and doors are open.

A

A

A

A

Figure 4

Failure to read and follow instructions in the operator's manual could result in death and/or bodily injury.

(at each wheel)

Items that you will need

Utility Knife

Unleaded Fuel (minimum 87 octane)

Items Included

FreshStart® Fuel

Preserver Cartridge

1 For mulching:

Leave the mulching cover and the installed mulching plug in place (Figure 5).

2 To convert to bagging:

Lift the rear door and remove the installed mulching plug (Figure 6).

Holding the rear door open, attach the grass bag to the rear of the mower (Figure 7).

Make sure the hooks on both sides of the bag frame hook onto the rear door rod (Figure 8).

Release the rear door (it will rest on top of the grass bag).

3 To convert to side discharge:

• Make sure the mulching plug is installed in the rear of the mower, and the grass bag is removed.

Lift the mulching cover, and install

Figure 9

 

the side discharge deflector onto the

 

 

mower deck (Figure 9).

 

• Make sure the deck tabs stick up through

 

 

the locking slots (Figure 10).

 

Release the mulching cover (it will rest

 

 

on top of the discharge deflector).

 

Mulching Plug

 

Side Discharge SAE30W

Operator’s

(Installed)

Grass Bag

Deflector

Oil

Manual

© Briggs & Stratton Corporation

Figure 6

 

Figure 8

 

 

 

We reserve the right to improve our products and make changes in specifications, designs, and standard equipment without notice and without incurring obligation.

Figure 10

Form No. 7105027 (Rev. ‘-’)

Page 1
Image 1
Snapper SPXV2270HW setup guide Unpack the mower Add oil and fuel, Raise the handle assembly, Final preparation