Manuals / Snapper / Lawn and Garden / Lawn Mower

Snapper S200KAV2561, S200XK2761 Regular Maintenance, Check Hydraulic Oil Level, B. Reservoir Cap

Models: S200KAV2561, S200XK2761

1 48

Download 48 pages 7.02 Kb

Page 30

Check Hydraulic Oil Level

Maintenance

Regular Maintenance

Check Hydraulic Oil Level

1.Before removing the reservoir cap, make sure the area around the reservoir cap and fill neck of the reservoir is free of dust, dirt, or other debris.

2.Unscrew the reservoir cap (B, Figure 24).

3.Look down the filler neck of the hydraulic oil reservoir

(A) and observe the oil level. When cold, the oil level should be approximately 4” (10 cm) below top of the filler neck.

4.If necessary, remove the reservoir cap (B) and add SAE 20W-50 motor oil.

5.Reinstall the reservoir cap.

Change Hydraulic Oil Filter

Change Interval: Every 250 Hours

Filter Part Number: 1719168

NOTE: Removing the oil filter from the filter base will drain the oil reservoir. Have a suitable container ready to catch any spilled oil. The manufacturer recommends this be a dealer-only service item.

1.Locate the transmission oil filter (B, Figure 25) at the rear of the battery compartment under the seat.

2.Lubricate the new filter base with a few drops of transmission oil. Fill the filter half full of oil.

3.Clean the area around the filter base and remove the filter. Do NOT drain the hydraulic system oil.

4.Thread the new filter onto the filter base until the gasket makes contact, then tighten 3/4 of a turn more.

5.Run the unit for several minutes and check the transmission oil level.

IMPORTANT NOTE: Use caution after changing the filter; air in the hydraulic system may affect the responsiveness of the control levers. Repeat step 5 until the air is out of the system.

B

A

Figure 24. Checking Hydraulic Oil Level

A.Hydraulic Oil Reservoir

B.Reservoir Cap

A

B

Figure 25. Battery Compartment

A.Hydraulic Oil Reservoir

B.Hydraulic Oil Filter

28	www.SnapperPro.com

Image 30

Snapper S200KAV2561, S200XK2761 manual Regular Maintenance, Check Hydraulic Oil Level, Change Hydraulic Oil Filter

Contents

Zero-Turn Riding Mower OPERATOR’S MANUALS200X Series Briggs & Stratton Yard Power Products GroupDATE PURCHASED See Features and Controls for the location of Identification NumbersContact Information Briggs & Stratton Yard Power Products Group 5375 N. Main St Munnsville, NYOperator Safety Safety Controls Operation Maintenance Troubleshooting SpecificationsTable of Contents Features & ControlsSafety Operator SafetyOperator Safety Safety Rules and Information OPERATING SAFETYSLOPE OPERATION Operator SafetySafety THROWN OBJECTSROLL BAR USE Operator SafetySafety RETAINING WALLS, DROP-OFFS, AND WATERFUEL AND MAINTENANCE Operator SafetySafety ENCLOSED AREASTRAINING Operator SafetySafety PREPARATIONSLOPE OPERATION Operator SafetySafety TOWED EQUIPMENT RIDE-ON UNITSSERVICE AND MAINTENANCE Operator SafetySafety Maintenance and StorageROLL BAR INSTRUCTIONS Operator SafetySafety OPERATIONAL WARNINGSINSPECTION AND MAINTENANCE OF THE ROLL BAR SEAT BELT Operator SafetySafety INSPECT WEBBINGSafety Decals Operator SafetySafety Operator Safety DANGERCAUTION or NOTICE SafetySafety Features and ControlsOperator Safety Identification NumbersSeat Adjustment Lever Features and ControlsControls Ignition SwitchHour Meter / Maintenance Reminder Features & ControlsPTO Power Take Off Switch Deck Lift Pedal, Cutting Height Adjustment Pin & Deck Lift Lock LeverOperation OperationOperation General Operating SafetyMowing Height Adjustment OperationSeat Adjustment Figure 4. Seat Adjustment A. Seat Adjustment LeverFigure 6. Foot Pedal Adjustment A. Deck Lift Foot Pedal Foot Pedal AdjustmentTo adjust pedal position THERE IS NO ROLL OVER PROTECTION WHEN THE ROLL BAR IS DOWNStarting the Engine OperationOperation Stopping the RiderZero Turn Driving Practice OperationOperation Smooth TravelPractice Turning Around a Corner OperationOperation Executing an End-Of-Row Zero TurnMowing OperationOperation Mowing RecommendationsHow Much Grass to Cut Off When Broadcasting When and How Often to MowNote Always operate the engine at full throttle when mowing OperationOperation Figure 18. Trailer Weight Recommendations A. Clevis Pin B. ClipOperation Attaching A TrailerMaintenance Regular MaintenanceRegular Maintenance Maintenance ScheduleEngine Maintenance Regular MaintenanceMaintenance Checking / Adding FuelLubrication Regular MaintenanceMaintenance GreaseFigure 25. Battery Compartment A. Hydraulic Oil Reservoir Regular MaintenanceMaintenance Check Hydraulic Oil LevelAlways wear gloves when handling mower blades or working near blades Regular MaintenanceMaintenance DANGERAlways wear gloves when handling the mower blades Regular MaintenanceMaintenance Always wear safety eye protection when grindingGround Speed Control Lever Adjustment Regular MaintenanceMaintenance Speed Balancing AdjustmentNeutral Adjustment Regular MaintenanceMaintenance Parking Brake AdjustmentReturn-To-Neutral Adjustment Regular MaintenanceMaintenance AdjustmentDeck Rod Timing Adjustment Regular MaintenanceMaintenance Deck Leveling AdjustmentMower Belt Replacement Regular MaintenanceMaintenance To avoid damaging belts, DO NOT PRY BELTS OVER PULLEYSHydraulic Pump Drive Belt Replacement Regular MaintenanceMaintenance Use extreme caution when removing this springBattery Maintenance Regular MaintenanceMaintenance NOTE This unit is equipped with a maintenance-free BCIU1 batteryBattery Service Regular MaintenanceMaintenance Checking Battery VoltageRegular Maintenance MaintenanceStorage Regular MaintenanceMaintenance Starting After Long Term StorageMaintenance TroubleshootingTroubleshooting Troubleshooting ChartTroubleshooting the Mower TroubleshootingTroubleshooting ProblemTroubleshooting Common Cutting Problems TroubleshootingTroubleshooting ProblemSpecifications SpecificationsSpecifications DIMENSIONSWarranty Period Owners Limited Warranty InformationFERRIS LIMITED WARRANTY Ferris Industries - a division of Simplicity Manufacturing IncENGINE Product SpecificationsCommon Service Parts BELTS AND BLADES